Bedienungsanleitung Yamaha MOX8 (Seite 41 von 76) (Englisch)

571303

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

MOX6/MOX8 Owner’s Manual

Quick Guide

6 Press the [REC] button to return to the Song

Record display.

7 Press the [P] (Top) button to return to the top of

the Song, then press the [F] (Play) button to start

recording.

As soon as the lead-in count (1-measure) is finished, play

the following notation.

8 After playing the above notation, press the [J]

(Stop) button to stop recording.

If you play any wrong notes, press the [J] (Stop) button,

then try recording again. Repeat as often as necessary until

you get it right.

9 Press the [P] (Top) button followed by the [F]

(Play) button to hear the recorded data.

The recorded data of the Tracks 1 and 2 will be played back.

To stop playback, press the [J] (Stop) button. If you are not

satisfied with the recorded data, try this operation again.

Creating a synthesizer part by

using Arpeggio

Next, record Arpeggio playback via Realtime Recording to

Track 3.

1 In the Song Play mode, select the same Song to

which the Drum and Bass parts have already been

recorded.

2 Press the ARP [ON/OFF] button so that its lamp

lights.

3 Press the [REC] button, followed by the [F1]

SETUP button, then set the parameters as below.

• “Type” = “replace”

• “Quantize” = “off”

• “Rec Track” = “3”

4 Press the [F2] VOICE button, followed by the

[CATEGORY SEARCH] button then select the

Synthesizer Voice.

Set the Main Category to “Synth Pad” then set the Sub

Category to “Analog.” Move the Cursor [>] button to call up

the Voice List. From this list, select “PRE5 H04 Saw Pad”

then press the [ENTER] button.

HINT

Re-recording a specific part of a Song

(Punch In/Out)

Use the Punch In/Out recording method to record over only a

specific portion of the Track. If you set the start point (Punch In)

and end point (Punch Out), and then start recording from the

top of the Song, the actual recording will be done only between

the Punch In and Punch Out points. In the eight-measure

example below, only the third through the fifth measures are re-

recorded.

NOTE Punch In/Out Recording can only be used with Realtime

recording.

NOTE

Note that the Punch In/Out method always replaces

(destroys) the original data over the specified area.

To execute Punch In/Punch Out recording in the above condition,

set the following parameters beforehand on the [F1] SETUP

display in the Song Record mode.

• “Type” = “punch”

• Punch In = 003:01

• Punch Out = 006:01

1234567 8

Recording start Recording stop

Before re-recording

Punch In point Punch Out point

After re-recording

Newly recorded data

NOTE For instructions on using the Location settings, see the

“Reference Manual” PDF document.

Punch Out point

Recording ends at this point and normal

playback of the recording Track starts.

Punch In point

Playback of the recording Track is turned off from this point,

and your keyboard performance will be recorded to the Track.

[SF1] COPYLOC button

Press the [SF1] COPY LOC to assign the measure numbers

registered to the Locations (Loc1 and Loc2) to the Punch

In and Punch Out points.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha MOX8 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha MOX8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info