557718
5
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
3
English
1 STANDBY/ON switch/indicator
This switch is used to set the MX-D1 to on or standby. A small amount of power is used in standby mode.
When the MX-D1 is turned on, this indicator lights blue and the MX-D1 is ready for use.
When the internal temperature rises, this indicator lights blue and purple alternately. If this happen, relocate this unit in a
well ventilated place and turn down the volume of the pre-amplifier etc.
When a fault is detected, the MX-D1’s protection system activates and this indicator lights red. If this happens,
set the MX-D1 to standby mode immediately and disconnect the AC power cable from the AC outlet.
If the indicator continues to light red when you re-connect the AC power cable, contact the nearest Yamaha dealer.
2 SPEAKER terminals
These terminals are for connecting your speakers.
They provide a reliable connection even with really
thick cables. Be sure to connect the left and right
channels, and the speaker polarities (+/-) correctly.
You can connect speakers with impedance of between
4 to 8 ohms.
3 BALANCE jacks
If your source component has balanced XLR output
jacks, connect them to these jacks using XLR cables.
4 MUTE button
You can temporarily mute the output from the MX-D1
by holding down this button. If you need to change
any input connections while the MX-D1 is still on,
hold down this button while you do it. This will
protect your speakers against possible damage due to
sudden loud noises, thumps, and clicks.
5 UNBALANCE jacks
If your source component has unbalanced RCA jacks
(labeled “AUDIO OUTPUT” on the YPC-1), connect
them to these jacks using an audio pin cable.
6 UNBAL/BAL switch
With this switch you can select the BALANCE jacks
or the UNBALANCE jacks.
7 AC IN connector
Connect the supplied AC power cable here.
e POWER switch
(Australia, U.K., Europe, China and Korea models)
Normally, set this switch to the ON position to use the
MX-D1.
To cut off the power supply from the AC line, set this
switch to the OFF position.
8 RS-232C terminal
9 AMP ID switch
0 CONTROL IN jack
q CONTROL OUT jack
w POWER/THROUGH switch
These are for control expansion. Consult your dealer
for details.
01-MX-D1_GB_E.fm Page 3 Wednesday, October 22, 2003 2:05 PM
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yamaha MX-D1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info