557718
9
Zoom out
Zoom in
Vorherige Seite
1/72
Nächste Seite
7
English
PWM (Pulse Width Modulation) theoretically produces zero quantization noise, a dynamic range that is dependent only
on circuit technology, and feedback, that combine to make the MX-D1 a superb high-performance power amplifier.
In addition, the Yamaha high-performance, high-speed analog and digital LSI chips are designed to optimize the
performance of the modulator and MOSFET drive circuits that form the heart of the MX-D1.
Active power control system
By continuously monitoring the amplifiers output current and controlling the maximum continuous output power and
instantaneous dynamic power, the MX-D1 always delivers maximum performance with any load impedance between 2
to 8 ohms.
Constant-gain PLL modulator circuit
With a conventional digital power amplifier, the output is adversely affected by fluctuations in power supply voltage as
the current demands of the amplifier change. The MX-D1’s modulation circuit, consisting of a PLL (Phase Locked Loop)
and modulation circuit, provides a radical solution to this problem.
In response to power supply voltage fluctuations, the constant-gain PLL modulator circuit produces a pulse-width
modulated waveform at a compensated modulation rate suitable for the input signal. In this way, linearity is maintained
and the open-loop gain is fixed, providing stable feedback.
Feedback
Digital output pulses are fed back in a cross-feedback circuit, which improves the performance of the modulator circuit
and the linearity of the output stage, providing very low distortion and a wide dynamic range.
In addition, an analog output signal taken from after the LC output filter is fed back to ensure a high damping factor and
a wide frequency response that is unaffected by the load impedance.
Protection system
The protection system, which guarantees safe operation, includes a super-fast current detection circuit that can measure
the current of a single pulse. It also includes safe operating sequential logic, DC detection, and over-current protection.
Switching power supply
Independent, high-efficiency, low noise resonant-type switching power supplies, developed by Yamaha, are used for the
left and right channels.
In addition, the secondary rectifier circuit has a magnetically coupled rectifier, which resolves issues normally associated
with conventional SEPP (single-ended push-pull) digital amplifiers and allows the MX-D1 to always maintain perfect
symmetry between the positive and negative power supply rails regardless of the direction of the output current.
01-MX-D1_GB_E.fm Page 7 Wednesday, October 22, 2003 2:05 PM
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yamaha MX-D1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info