Bedienungsanleitung Yamaha P-255 (Seite 43 von 60) (Englisch)

583118

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Customizing with Function Parameters

P-255 Owner’s Manual

The following parameters can be used to adjust the split

point and make various other settings for Split mode in

order to best suit the piece you intend to play. Settings can

be made for each combination of Voices as described

below.

Activate Split mode, select the Voices you wish to

use, and then use the [FUNCTION] button to select

the Function parameter(s) you wish to set.

Change the setting(s) using the [-/NO] and [+/YES]

buttons.

Shortcut:

Yo u can jump directly to Function parameter F4.1 by pressing

the [FUNCTION] button with the [SPLIT] button held down.

F4.1 Split point

Use this parameter to set the location at which the keyboard

is divided into the left and right sides. The key that defines

the split point is included in the left side of the keyboard.

•Available settings: A-1 to C7 (entire keyboard)

•Default setting: F#2

Examples of split points as shown on display

F4.2 Split balance

This parameter can be used to optimize the volume balance

between the split Voices. Settings can be made for each

combination of Voices.

•Available settings: 0 to 20 (The greater the value, the louder the

volume of the right Voice; 10 represents an equal balance.)

•Default setting: Each combination of Voices has its own default.

F4.3 Right Voice octave shift

F4.4 Left Voice octave shift

These parameters are used to raise or lower the pitch of

each of the left and right Voices in units of one octave. This

allows you to set the note ranges of each side of the key-

board to better suit the pieces you intend to play. Settings

can be made for each combination of Voices.

•Available settings: -1, 0, and 1

•Default setting: Each combination of Voices has its own default.

F4.5 Right Voice effect depth

F4.6 Left Voice effect depth

Use these parameters to set the depth of the effect for each

of the left and right Voices.

•Available settings: 0 to 20

•Default setting: Each combination of Voices has its own default.

F4.7 Damper pedal range

This parameter can be use to specify whether the damper

pedal should affect both Voices (“ALL”), only the right

Voice (“1”), or only the left Voice (“2”).

•Available settings: ALL (both Voices), 1 (right Voice only), and 2

(left Voice only)

•Default setting: 1

F4.8 Reset

By pressing the [+/YES] button with this Function parame-

ter shown, you can reset all of the Split mode settings to the

defaults for the corresponding Voice combinations.

The following parameters can be used to assign the func-

tionality of the [PLAY/STOP] button to a pedal, adjust the

depth of the damper pedal’s resonance effect, and make a

range of other convenient settings.

F5.1

Pedal [PLAY/STOP] function

If you have connected a pedal unit* (see page 12) to your

digital piano, you can use this parameter to configure either

the center or left pedal to operate in the same way as the

control panel’s [PLAY/STOP] button. Note that when this

functionality is assigned to a pedal, the pedal’s original

function (i.e., soft or sostenuto) will be disabled. (*: Sold

separately.)

•Available settings: OFF, 1 (left pedal), and 2 (center pedal)

•Default setting: OFF

F5.2 Damper-pedal resonance depth

Using this parameter, you can adjust the depth of the reso-

nance effect applied to certain Voices—specifically, Grand

Piano, Live Grand, Ballad Grand, and Bright Grand—when

the damper pedal is operated.

•Available settings: 0 to 10

•Default setting: Differs for each Voice

F5.3 Soft pedal effect depth

If you have connected a pedal unit* (see page 12), the soft

pedal will slightly lower the volume and soften the timbre

of notes played while it is being operated, and using this

parameter, you can adjust the depth of that effect. (*: Sold

separately.)

•Available settings: 1 to 10

•Default setting: 5

F4. Split mode settings

• As an alternative to using the [-/NO] and [+/YES] buttons, the split point can be

set by pressing the corresponding key. You can also do this when Function

parameter F4.1 is not being shown by pressing the key with the [SPLIT] button

held down (page 14).

NOTE

2 F~2 E_2

Indicates a sharp

key (#).

Indicates a flat

key (b).

F2 F#2Eb2

F5.

Pedal and special sound settings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha P-255 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha P-255

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info