Bedienungsanleitung Yamaha RX-V2400 (Seite 82 von 91) (Englisch)

558954

Zoom out

Zoom in

Vorherige Seite

1/91

Nächste Seite

TROUBLESHOOTING

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below

or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact the

nearest authorized YAMAHA dealer or service center.

■ General

TROUBLESHOOTING

Problem Cause Remedy

Refer to

page

This unit fails to turn

on when STANDBY/

ON (or SYSTEM

POWER) is pressed,

or enters in the

standby mode soon

after the power has

been turned on.

The power cord is not connected or the

plug is not completely inserted.

Connect the power cord firmly.

—

The impedance setting is incorrect. Set the impedance to match your speakers.

The protection circuitry has been

activated.

Make sure all speaker wire connections on this unit

and on all speakers are secure and that the wire for

each connection does not touch anything other than

its respective connection.

12—14

This unit has been exposed to a strong

external electric shock (such as lightning

and strong static electricity).

Set this unit in the standby mode, disconnect the

power cord, plug it back in after 30 seconds, then use

it normally.

—

On screen display

does not appear.

The setting for the on-screen display is set

to “DISPLAY OFF”.

Select the full or short display mode.

GRAY BACK in the SET MENU is set to

OFF, and no video signal is currently

being received.

Set GRAY BACK to AUTO to always show the OSD.

No sound Incorrect input or output cable

connections.

Connect the cables properly. If the problem persists,

the cables may be defective.

16—19

INPUT MODE is set to DTS or

ANALOG.

Select AUTO.

No appropriate input source has been

selected.

Select an appropriate input source with INPUT,

MULTI CH INPUT or the input selector buttons.

Speaker connections are not secure. Secure the connections.

The front speakers to be used have not

been selected properly.

Select the front speakers with SPEAKERS A and/or

The volume is turned down. Turn up the volume.

—

The sound is muted. Press MUTE or any operation buttons of this unit to

cancel a mute and adjust the volume.

If you are playing an LD source, the

player may not output digital signals if the

LD source was not digitally recorded.

Set the INPUT MODE to ANALOG.

The INPUT MODE is set to ANALOG

while playing a source encoded with a

DTS signal.

Set the INPUT MODE to AUTO or DTS.

The signals this unit cannot reproduce are

being received from a source component

e.g.: a CD-ROM.

Play a source whose signals this unit can reproduce.

—

No picture The output and input for the picture are

connected to different types of video

jacks.

Turn on the video conversion function.

01EN00_RX-V2400RDS_EN.book Page 80 Thursday, November 6, 2003 11:49 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V2400 Seite 82

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V2400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info