Bedienungsanleitung Yamaha RX-V2400 (Seite 83 von 91) (Englisch)

558954

Zoom out

Zoom in

Vorherige Seite

1/91

Nächste Seite

English

TROUBLESHOOTING

ADDITIONAL

INFORMATION

Problem Cause Remedy

Refer to

page

The sound suddenly

goes off.

The protection circuit has been activated

because of a short circuit, etc.

Check that the impedance selector setting is correct.

Check the speaker wires are not touching each other

and then turn this unit back on.

—

The sleep timer has turned the unit off. Turn on the power, and play the source again.

—

The sound is muted. Press MUTE to cancel a mute.

Only the speaker on

one side can be

heard.

Incorrect cable connections. Connect the cables properly. If the problem persists,

the cables may be defective.

Incorrect balance settings in the SET

MENU.

Adjust the SP LEVEL settings.

Only the center

speaker outputs

substantial sound.

When playing a monaural source with a

CINEMA DSP program, the source signal

is directed to the center channel, and the

front and surround speakers output effect

sounds.

No sound from the

effect speakers.

The sound field programs are turned off. Press STRAIGHT/EFFECT to turn them on.

A Dolby Surround, Dolby Digital or DTS

decoding DSP program is being used with

material not encoded with Dolby

Surround, Dolby Digital or DTS.

Select another sound field program.

No sound from the

center speaker.

The output level of the center speaker is

set to minimum.

Raise the level of the center speaker.

“CENTER SP” in the SET MENU is set

to NONE.

Select the appropriate mode for your center speaker.

One of the Hi-Fi DSP programs (except

for 7ch Stereo) has been selected.

Select another sound field program.

No sound from the

surround speakers.

The output level of the surround speakers

is set to minimum.

Raise the output level of the surround speakers.

“SURR. LR SP” in the SET MENU is set

to NONE.

Select the appropriate speaker mode for the surround

L/R speakers.

A monaural source is being played with

STRAIGHT/EFFECT set to STRAIGHT.

Press STRAIGHT/EFFECT to turn on the sound

fields. Then select another sound field program.

—

No sound from the

surround back

speakers.

Presence speakers are selected. Select surround back speakers in PR/SBch SELECT.

“SURR. LR SP” in the SET MENU is set

to NONE.

If the speaker mode for the surround L/R speakers is

set to NONE, the speaker mode for the surround back

speaker is automatically set to NONE. Select the

appropriate speaker mode for the surround L/R

speaker mode.

“SURR.B SP” in the SET MENU is set to

NONE.

Select LRG or SML.

No sound from the

subwoofer.

“LFE/BASS OUT” in the SET MENU is

set to FRONT when a Dolby Digital or

DTS signal is being played.

Select SWFR or BOTH.

“LFE/BASS OUT” in the SET MENU is

set to SWFR or FRONT when a 2-channel

source is being played.

Select BOTH.

The source does not contain low bass

signals.

01EN00_RX-V2400RDS_EN.book Page 81 Thursday, November 6, 2003 11:49 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V2400 Seite 83

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V2400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info