Bedienungsanleitung Yamaha RX-V3000RDS (Seite 43 von 78) (Englisch)

549968

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

English

SET MENU Items

■ 1G. MAIN LEVEL

Change this setting if you cannot match the sound volume of the Front, Rear, and Center speakers with the Main speakers because of the

unusually high efficiency performance of the Main speakers. The initial setting is “Normal”.

Select the “Normal” setting if you can match the volume of your effect speakers with the volume of your Main speakers using the

Dolby Surround Test.

Select the “–10dB” setting if you cannot match the volume of your effect speakers with the volume of your Main speakers using the

Dolby Surround Test.

Notes:

• When 96-kHz sampling digital signals are input to this unit, level adjustments in items 1B and 1E are possible, but those in items 1A, 1C, 1D and 1F

are not affected.

• When 6CH INPUT is selected as the input source, level adjustments in items 1A through 1F are not affected.

1G MAIN LEVEL

“Normal -10dB

1G MAIN LEVEL

“Normal -10dB

1G MAIN LEVEL

Normal “-10dB

Normal –10dB

2. LOW FREQ. TEST

Use this feature to adjust the Subwoofer volume so it matches the volume of the other speakers in your configuration. Change the setting

using the remote control while sitting in the main listening position.

Press + or – to set the TEST TONE to “ON”, and adjust the volume using VOLUME + so you can hear the tone.

Press g repeatedly to go to OUTPUT and press + or – to select the speaker you want to compare with the Subwoofer.

• If “SUBWOOFER” is selected, test tones above 90 Hz will not be output from the Subwoofer. The test tone will not necessarily be

output from the selected speakers. The output mode of the test tone depends on the settings of the 1. SPEAKER SET items in the

SET MENU.

Press g repeatedly to go to FREQ. and press + or – to select the frequency you want to use.

Adjust the Subwoofer volume using the controls on the Subwoofer so it matches the volume of the speaker you are comparing it to.

Notes:

• Do not turn up the VOLUME too high.

• If no test tone is heard, turn off the power and make sure all the necessary hookups are correct.

• When the headphones are connected to this unit, you cannot set the TEST TONE to “ON”.

■ About the test tone

The test tone is produced by the tone generator.

The tone generator produces a narrow band of noise centered at a specified

frequency by the band pass filter.

You can change the center frequency from 35 Hz through 250 Hz in one-sixth

octave steps.

You can use the test tone not only for adjusting the subwoofer level, but also for

checking the low frequency characteristics of your listening room. Low frequency

sounds are especially affected by the listener’s position, speaker placement,

subwoofer polarity, and other conditions.

2 LOW FREQ.TEST

TEST TONE………OFF

2 LOW FREQ.TEST

OUTPUT…MAIN L/R

2 LOW FREQ.TEST

FREQ.………………88Hz

2 LOW FREQ.TEST

≥ TEST TONE………OFF

OUTPUT…MAIN L/R

FREQ.………………88Hz

2 LOW FREQ.TEST

TEST TONE…………ON

≥ OUTPUT…MAIN L/R

FREQ.………………88Hz

2 LOW FREQ.TEST

TEST TONE…………ON

OUTPUT…MAIN L/R

≥ FREQ.………………88Hz

35 Hz~250 Hz

Band Pass Filter

Center freq.

Digital Generator

(Wide Band Noise Produced)

NOISE

FREQ.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V3000RDS Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info