Bedienungsanleitung Yamaha RX-V3067 (Seite 48 von 166) (Englisch)

516915

Zoom out

Zoom in

Vorherige Seite

1/166

Nächste Seite

CONNECTIONS

Setting up the speaker parameters automatically (YPAO)

En 48

Select the desired menu item (or enable a

function) using iCursor B / C / D / E and

iENTER.

Press iRETURN to finish the Result menu.

■

Reloading automatic setup

parameters

If you are not satisfied with the fine-adjustment of setup

parameters with Manual Setup, the result of automatic

setup saved on this unit can be reloaded. Select “Setup

Reload” in the Result menu.

■

When an error message is

displayed during measurement

See “Error messages” (☞p. 50) for instructions on

resolving the problem and measure acoustics again.

Check the error code displayed and use YPAO to

measure acoustics again as described below.

When “E-1,” “E-2,” “E-3,” “E-4,” “E-6” or “E-11”

is displayed:

Press iENTER.

Press iCursor E to select “EXIT.”

Press iENTER to terminate YPAO, and

switch the unit to standby mode.

Check that the speakers are properly

connected.

Turn on the unit and use YPAO again.

RETURN

ENTER

SOU

ECEIVE

-A

LTI

TUNER

[

]

[

]

Wiring Displays the speakers connected to this

unit and the polarity of each connected

speaker.

• “Normal” is displayed when the

polarity of the connected speaker is

normal.

• “Reverse” is displayed when the

polarity of the connected speaker is

opposite.

Size Displays the size of the connected

speakers and the bass cross over

frequency (“Bass Crossover”).

• “Large” is displayed when the

connected speaker has the ability to

reproduce the low-frequency signals

effectively.

• “Small” is displayed when the

connected speaker does not have the

ability to reproduce the low-frequency

signals effectively.

Distance Displays the distance from the listening

position to speakers. The unit for distance

can be switched between “ft” (feet) and

“m” (meter) by pressing iCursor D / E.

Level Displays the result of the adjustment of

each connected speaker output level.

Angle Displays the angles of the front speakers,

surround speakers, front presence

speakers and rear presence speakers at the

measured point.

Setup Reload J1 Clears the fine-adjustment with Manual

Setup and reloads the result of automatic

setup. For details, refer to “Reloading

automatic setup parameters.”

The result of automatic setup can be fine-tuned

manually by “Manual Setup.” Refer to “Manual

speaker setup” (☞

p. 98) for details.

NOTE

When automatic setup parameters are reloaded,

manually configured settings are cleared. To avoid

clearing manually configured settings by reloading

automatic setup parameters, see “Prohibiting setting

changes” (☞

p. 114).

Continues to the

1 : This item is displayed after the fine-adjustment is performed with

“Manual Setup.” Use this item to return the settings to the result

of automatic setup.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V3067 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V3067

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info