Bedienungsanleitung Yamaha RX-V3067 (Seite 50 von 166) (Englisch)

516915

Zoom out

Zoom in

Vorherige Seite

1/166

Nächste Seite

En 50

CONNECTIONS

Setting up the speaker parameters automatically (YPAO)

■

Message list

■ When a warning message is displayed before measurement

■ Error messages

■ Warning messages

NOTE

If the following messages appear, resolve the problems that have occurred and carry out the

measurement process again.

Connect MIC! The YPAO microphone is not connected. Connect the YPAO microphone to the YPAO MIC

jack on the front panel.

Unplug HP! The headphones are connected. Remove the headphones.

Memory Guard! The settings of this unit are protected. Set “Memory Guard” in the Setup menu to “Off”

(☞p. 114).

E-1:

No Front SP

The unit was not able to find the front

channel.

Check that the left and right front speakers are

connected correctly.

E-2:

No Sur. SP

The unit was only able to find one of side

of the surround channels.

Check that the left and right surround speakers are

connected correctly.

E-3:

No F.PRNS SP

The unit was only able to find one of side

of the front presence channels.

Check that the left and right front presence speakers

are connected correctly.

E-4:

SBR→SBL

Only one surround back speaker is

connected and only the right side surround

back channel sound is detected.

When only one surround back speaker is connected,

connect to the left side (SINGLE) terminal.

E-5:

Noisy

The noise is too loud, preventing accurate

measurements from being taken.

Measure again in quiet surroundings. Turn off any

devices in the room that may be emitting noise, or

place them further away from the YPAO

microphone.

When this message is displayed, selecting

“PROCEED” will allow you to continue measuring.

However, we recommend resolving the problem and

measuring again, as continuing measurement without

doing so will not give accurate results.

E-6:

Check Sur.

Even though surround left and right

speakers are not connected, only the

surround back speakers are connected.

When using surround back speakers, connection of

the surround left/right speakers is necessary.

E-7:

No MIC

The YPAO microphone has been removed. While measuring, take care not to touch the YPAO

microphone.

E-8:

No Signal

The YPAO microphone could not

distinguish a test tone.

Check that the YPAO microphone has been

installed correctly.

Check that each speaker has been connected and

installed correctly.

The YPAO microphone or the YPAO MIC jack may

be broken. Inquire at the retailer where you

purchased this unit, or the nearest Yamaha service

center.

E-9:

User Cancel

You have carried out an operation that has

cancelled the measuring process.

Carry out the measuring process again. Do not

operate this unit by, for example, adjusting the

volume.

E-10:

Internal Error

An internal error has occurred. Carry out the measuring process again. Contact a

Yamaha service center if “E-10” is displayed again.

E-11:

No R.PRNS SP

The unit was only able to find one of side

of the rear presence channels.

Check that the left and right rear presence speakers

are connected correctly.

W-1:

Out of Phase

The speakers displayed are connected with

the opposite polarity. Depending on the

type of speakers you are using and the

environment in which you have them

installed, this message may occur even if

the speakers are connected correctly.

Depending on the type of speakers, “W-1” may

display even if the speakers are connected correctly.

Check that the speaker polarity + (positive), and -

(negative) are correct. If these are connected

correctly, you can use the speakers normally even

this message appears.

W-2:

Over 24m/80ft

The speakers displayed are separated from

the listening position by more than 24 m,

and cannot be adjusted correctly.

Install the speakers with 24 m of the listening

position.

W-3:

Level Error

Volume level varies greatly for individual

channels, and cannot be adjusted correctly.

Check that all speakers are installed in the same

surroundings.

Check that the speaker polarity + (positive), and -

(negative) are correct.

We recommend the same speakers or speakers with

as similar specifications as possible.

Adjust the volume of the subwoofer.

If “W-2” or “W-3” appears, you can apply measurement results, but they will not give optimal

results. We recommend that you resolve the problem and carry out the measurement process again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V3067 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V3067

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info