Bedienungsanleitung Yamaha RX-V565 (Seite 53 von 332) (Deutsch, Englisch, Holländisch, Französisch, Schwedisch)

464173

Zoom out

Zoom in

Vorherige Seite

1/332

Nächste Seite

49 En

Troubleshooting

English

INTRODUCTION

APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

No picture. An appropriate video input is not selected

on the monitor.

Select an appropriate video input on the monitor. —

The composite output terminals are used

to output a component video signal, or the

COMPONENT VIDEO jacks are used to

output a composite video signal.

If your monitor does not support the HDMI

connection, connect it to the COMPONENT OUT

jacks or the composite output terminals and select an

appropriate video input on the monitor.

This unit outputs the video signals are not

supported on the video monitor connected

to the HDMI OUT jack.

Displays the advanced setup menu and select

“VIDEO” in “INIT” to reset the video parameters.

Displays the advanced setup menu and set

“MON.CHK” to “YES.”

Non-standard video signals are input. Connect the monitor to this unit via the

COMPONENT OUT jacks or the composite output

terminals.

The sound suddenly

goes off.

The protection circuitry has been activated

because of a short circuit, etc.

Check that the speaker wires are not touching each

other and then turn this unit back on.

—

The sleep timer has turned off this unit. Turn on this unit, and play the source again. —

Sound is heard from

the speaker on one

side only.

The playback component or speakers are

not connected properly.

Connect the cables properly. If the problem persists,

the cables may be defective.

The speaker level settings are incorrect. Adjust “B)Level” settings. 43

Only the center

speaker outputs

substantial sound.

When a monaural source sound field

program is applied, sound of all channels

are output from the center speaker for

some surround decoders.

Try another sound field program. 24

No sound is output

from a specific

speaker.

Output from that speaker is disabled. Check the Speaker indicators on the front panel

display. If the corresponding indicator is turned off,

try the following.

1) Change the input source to another one.

2) With the selected sound field program, sound is not

output from that speaker. Select another sound field

program.

3) “None” may have been selected for that speaker on

this unit. Display Speaker Setup in the Setup menu

and enables output of that speaker.

6, 21, 24,

The volume of that speaker is set to

minimum in Speaker Setup in the Setup

menu.

Display Speaker Setup in the Setup menu and adjust

the volume (2 Manual Setup→B)Level).

This unit or speaker is malfunction. Check the Speaker indicators on the front panel

display. If the corresponding indicator lights up,

connect another speaker and check if sound is output.

If sound is not output, this unit may be malfunction.

6, 10

No sound is heard

from the surround

speakers.

This unit is in the “STRAIGHT” mode

and a monaural source is being played

back.

Press LSTRAIGHT or the jSTRAIGHT on the

remote control to turn off the “STRAIGHT” mode.

Sound may not be output from certain

channels depending on input sources or

sound field programs.

Try another sound field program. 24

Problem Cause Remedy

See

page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V565 Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V565

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info