Bedienungsanleitung Yamaha RX-V565 (Seite 51 von 332) (Deutsch, Englisch, Holländisch, Französisch, Schwedisch)

464173

Zoom out

Zoom in

Vorherige Seite

1/332

Nächste Seite

47 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

In the advanced setup, you can set basic operations of this

unit, such as on and off of a bi-amp connection, or

initialize user settings. Perform the following steps to

change settings.

1 Set this unit to the standby mode.

2 Press ASTANDBY/ON while pressing and

holding LSTRAIGHT on the front panel.

The advanced setup menu appears on the front panel

display.

3 Press KPROGRAM l / h repeatedly to

select the parameter you want to change.

The default setting are marked with “*.”

• Set values are placed in XXX of the following parameters on an

actual display screen.

REMOTE ID -XXX

Sets a remote control ID. When using multiple

Yamaha AV receivers, you can operate them with a

single remote control by setting the receiver IDs to

the same setting.

BI AMP - XXX

Switches on and off of bi-amp connection of main

speakers. For bi-amp connection, see page 12.

MON.CHK - XXXX

Adds upscaling limitation on output signals to a video

monitor connected to this unit via the HDMI OUT

jack.

INIT-XXXXXXXXX

Initializes various settings stored in this unit. You can

select an initialization method from the following.

DSP PARAM: All parameters of sound field

programs

VIDEO: Video conversion settings (resolution/

aspect) in the setup menu and the OSD

display position

ALL: Reset this unit to initial factory

settings

CANCEL: Cancellation of initialization

4 Press LSTRAIGHT a few times to select the

value you want to change.

The value selected here becomes effective when this

unit is turned on the next time. You can change

multiple settings by repeating steps 3 and 4.

5 Press ASTANDBY/ON, turns off this

system, and press ASTANDBY/ON again.

The value set in step 3 becomes effective, and this

unit turns on. When you select initialization in step 3,

the initialization is performed.

Two IDs are provided for the remote control of this unit. If

another Yamaha amplifier is in the same room, setting a

different remote control ID to this unit prevents unwanted

operation of the other amplifier.

ID1 is set for both remote control and amplifier by default.

When you change the remote control ID, display

“Advance Setup” (see the previous section) and change the

ID for the amplifier too.

1 Press cCODE SET on the remote control

using a pointed object such as the tip of a

ballpoint pen.

bTRANSMIT blinks twice.

2 Press lSETUP on the remote control.

3 Enter the desired remote control ID code.

To switch to ID1:

Enter “5019” using sNumeric keys.

To switch to ID2:

Enter “5020” using sNumeric keys.

Once the remote control code is registered,

bTRANSMIT blinks twice.

If it fails, bTRANSMIT blinks six times. Repeat

from step 1.

• Initializing the remote control code (see page 46) returns it to ID1.

Advanced setup

Choices: ID1*/ID2

Choices: ON/OFF*

Choices: YES*/SKIP

Choices: DSP PARAM/VIDEO/ALL/CANCEL

ADVANCEDSETUP

Setting a remote control ID

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V565 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V565

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info