Bedienungsanleitung Yamaha RX-V661 (Seite 99 von 109) (Englisch)

464163

Zoom out

Zoom in

Vorherige Seite

1/109

Nächste Seite

97 En

Using multi-zone configuration

ADVANCED

OPERATION

English

Operating Zone 2

Rotate the

INPUT selector to select the

desired input source while the ZONE2 indicator

is flashing in the front panel display.

• Select “TUNER” as the input source to use the TUNER

features in Zone 2. For details about the TUNER

operations, see “FM/AM tuning” on page 50.

• Select “V-AUX” as the input source to use iPod

features in Zone 2. For details about the iPod

operations, see “Using iPod™” on page 56.

You must complete this step within 10 seconds while the selected

zone flashes in the front panel display. Otherwise, the currently

selected zone mode is automatically canceled. In this case, press

ZONE CONTROL on the front panel again.

Set Zone 2 to the standby mode

Press

ZONE 2 ON/OFF to set Zone 2 to the

standby mode.

■ Controlling Zone 2 with the remote

control

Activating the Zone 2 operation mode

Set the operation mode selector to

AMP and

then press

SELECT k repeatedly to select the

zone you want to control.

“ZONE 2” is displayed in the display window (

) on the

remote control.

Turning on or off Zone 2 using the remote control

POWER and

STANDBY on the remote control

work differently depending on the selected zone that

appears in the display window (

) on the remote control.

• When the main zone, Zone 2 mode is selected, you can

turn on the main zone or Zone 2 or set them to the

standby mode individually.

• When the all mode is selected, pressing

POWER

turns on the main zone and Zone 2 simultaneously and

pressing

STANDBY sets them to the standby mode

simultaneously.

• When the remote control is in the main zone mode, “MAIN”

appears for a few seconds when

POWER or

STANDBY

is pressed.

• “ALL” appears in the display window (J) on the remote

control only when SELECT n is pressed.

Selecting the input source of Zone 2

Press one of the input selector buttons (

) to

select the input source of the selected zone.

If the remote control is used to select the input source, “2;

name of the selected input area” is displayed in the display

window (

) on the remote control when Zone 2 is

selected respectively.

The selected input source is shared across all zones.

Operate the following operations after activating the Zone 2

operation mode.

SELECT

SOURCE

AMP

Control mode

Display window

(J)

POWER

and

STANDBY

Main zone

mode

Name of the selected

input area

Turns on the main

zone only or sets it to

the standby mode.

Zone 2 mode

“ZONE 2” or “2;name

of the selected input

area”

Turns on Zone 2 or

sets it to the standby

mode.

All mode

“ALL”

POWER: turns

on the main zone and

Zone 2.

STANDBY: sets

the main zone and

Zone 2 to the standby

mode.

Notes

Note

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V661 Seite 99

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V661

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info