Bedienungsanleitung Yamaha RX-V661 (Seite 101 von 109) (Englisch)

464163

101

Zoom out

Zoom in

Vorherige Seite

1/109

Nächste Seite

99 En

Advanced setup

ADVANCED

OPERATION

English

■ Speaker impedance SP IMP.

Use this feature to set the speaker impedance of this unit

so that it matches that of your speakers.

Choices: 8Ω MIN, 6Ω MIN

•Select “8Ω MIN” to set the speaker impedance to 8 Ω .

• Select “6Ω MIN” to set the speaker impedance to 6 Ω .

The Canada model cannot use two separate speaker systems

(A and B) simultaneously when “SP IMP.” is set to “8Ω MIN”.

■ User presets PRESET

Use this feature to reset all the parameters of this unit to

the initial factory settings (see page 109).

Choices: CANCEL, RESET

• Select “CANCEL” not to reset any parameters of this

unit.

• Select “RESET” to reset the parameters of this unit.

• This setting completely resets all the parameters of this unit

including the “SET MENU” parameters.

• The initial factory settings are activated next time you turn on

this unit.

■ Remote control AMP ID REMOTE AMP

Use this feature to set the AMP ID of this unit for remote

control recognition. This feature is useful when you

operate this unit and the other Yamaha receivers/

amplifiers in the same room separately.

Choices: ID1, ID2

• Select “ID1” when the remote control AMP ID code is

set to “2001”.

• Select “ID2” when the remote control AMP ID code is

set to “2002”.

Setting remote control AMP ID codes

You need to set the remote control AMP ID code for the

remote control.

1 Set the operation mode selector to

AMP or

SOURCE.

2 Press and hold

LEARN for about 3

seconds using a ballpoint pen or similar

object and then press

l / h repeatedly

until “L;AMP” appears in the display window

(

) on the remote control.

• Be sure to press and hold

LEARN for at least 3

seconds, otherwise the learning process will start.

• If you do not complete each of the following steps within

30 seconds, the setting mode will be automatically

canceled. In this case, start over from step 1.

3 Press

ENTER.

The four-digit code set for the selected input area

appears in the display window (

) on the remote

control.

See page 98 for the operation of the advanced setup.

SP IMP. Speaker Impedance level

8Ω MIN

Front

If you use one set (A or B),

the impedance of each

speaker must be 8 Ω or

higher.

If you use two sets (A and

B), the impedance of each

speaker must be 16 Ω or

higher.

Center

The impedance of each

speaker must be 8 Ω or

higher.

Surround

Surround back

6Ω MIN

Front

If you use one set (A or B),

the impedance of each

speaker must be 4 Ω or

higher.

If you use two sets (A and

B), the impedance of each

speaker must be 8 Ω or

higher.

Center

The impedance of each

speaker must be 6 Ω or

higher.

Surround

Surround back

Notes

LEARN

ENTER

A/B/C/D/E

PRESET/CH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V661 Seite 101

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V661

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info