Bedienungsanleitung Yamaha RX-V863 (Seite 34 von 801) (Deutsch, Englisch, Holländisch, Französisch, Schwedisch)

464169

Zoom out

Zoom in

Vorherige Seite

1/801

Nächste Seite

OPTIMIZING THE SPEAKER SETTING FOR YOUR LISTENING ROOM (YPAO)

32 En

This unit employs the YPAO (Yamaha Parametric Room Acoustic Optimizer) technology which lets you avoid

troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. The supplied

optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening

environment.

• Be advised that it is normal for loud test tones to be output

during the “AUTO SETUP” procedure.

• To achieve the best results, make sure the room is as quiet as

possible while the “AUTO SETUP” procedure is in progress. If

there is too much ambient noise, the results may not be

satisfactory.

• Initial settings are indicated in bold.

• You can run “AUTO SETUP” using the system menu that

appears in the OSD or in the front panel display. This manual

uses the OSD illustrations to explain the “AUTO SETUP”

procedure.

• Before performing operations, set the operation mode selector

on the remote control to

AMP.

• This unit uses the speakers connected to the FRONT A speaker

terminals as the front speakers for the adjustment.

1 Make sure of the following check points.

Before starting the automatic setup, check the following

check points.

❏ Speakers are connected appropriately.

❏ Headphones are disconnected from this unit.

❏ This unit and the video monitor are turned on.

❏ This unit is selected as the video input source of

the video monitor.

❏ The connected subwoofer is turned on and the

volume level is set to about half way (or slightly

less).

❏ The crossover frequency controls of the

connected subwoofer is set to the maximum.

❏ The room is sufficiently quiet.

If you connect two subwoofers to this unit, the volume level

of each subwoofer is set to slightly less.

2 Connect the supplied optimizer microphone

to the OPTIMIZER MIC jack on the front

panel.

“MIC ON View OSD menu” appears in the front

panel display.

The following menu screen appears on the video

monitor.

3 Place the optimizer microphone at your

normal listening position on a flat level

surface with the omni-directional

microphone heading upward.

It is recommended that you use a tripod (etc.) to affix the

optimizer microphone at the same height as your ears would

be when you are seated in your listening position. You can

use the attached screw of a tripod (etc.) to fix the optimizer

microphone to the tripod (etc.).

Optimizing the speaker setting for your listening room (YPAO)

Using AUTO SETUP

Notes

Note

VOLUME

MIN

MAX

MIN MAX

CROSSOVER

HIGH CUT

Controls of a subwoofer (example)

VIDEO AUX

OPTIMIZER MIC

S VIDEO

VIDEO AUDIO

OPTICAL

Omni-directional

microphone

AUTOSETUP

ZONEBPRESENCE

. EXTRASPASSIGN

>ZONE2 FRONTB

[]/[]:Select

NONE

SETUP;;;;;;;AUTO

EQ;;;;;;;NATURAL

START

[]/[]:Up/Down

[

Optimizer microphone

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V863 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V863

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info