Bedienungsanleitung Yamaha RX-V863 (Seite 36 von 801) (Deutsch, Englisch, Holländisch, Französisch, Schwedisch)

464169

Zoom out

Zoom in

Vorherige Seite

1/801

Nächste Seite

34 En

Optimizing the speaker setting for your listening room (YPAO)

7 Press

n to select “START” and then press

ENTER to start the setup procedure.

The following message appears in the OSD.

When this unit starts the automatic setup procedure,

loud test tones are output at the speakers.

For more accurate measurements, keep quiet and

move to the wall where speakers are not around. We

recommend that you leave the listening room during

the automatic setup procedure.

Once you perform the next operation, this unit starts

the automatic setup procedure.

8 Press

ENTER to start the automatic setup

procedure.

The following screen appears in the OSD and setup

procedure starts in 10 seconds.

Loud test tones are output from each speaker during

the auto setup procedure. Once all items are set, the

“RESULT” display appears in the OSD.

• During the automatic setup procedure, do not perform any

operation on this unit.

• We recommend that you get out of the room while this unit

is in the auto setup procedure. It takes approximately 3

minutes for this unit to complete the auto setup procedure.

Press

k to cancel the automatic setup procedure.

9 Make sure that the following screen appears

and then press

ENTER to display the

result screen.

The results displayed under “RESULT” are as

follows:

Number of speakers SP

Displays the number of speakers connected to this

unit in the following order:

Front/Back/Subwoofer

Speaker distance DIST

Displays the speaker distance from the listening

position in the following order:

Closest speaker distance/Farthest speaker distance

Speaker level LVL

Displays the speaker output level in the following

order:

Lowest speaker output level/Highest speaker output

level

• The signal output at the SUBWOOFER PRE OUT 2 jack

is the same as the one output at the SUBWOOFER PRE

OUT 1 jack. Therefore, even if you connect two

subwoofers, the number of the connected subwoofer is

indicated as “0.1”.

• If “E-10:INTERNAL ERROR” appears during the testing

procedure, restart from step 4.

• If you selected other than “AUTO” in step 5, no test tones

are output.

• If an error occurs during the “AUTO SETUP” procedure,

the setup procedure is canceled and an error screen

appears. For details, see “If an error screen appears” on

page 36.

• When this unit detects potential problems during the

“AUTO SETUP” procedure, “WARNING” and the

number of warning messages appears in the above of

“RESULT” (see page 36).

• Depending on the listening environment, “SWFR

PHASE:REV” appears during the automatic procedure

and “SUBWOOFER PHASE” in “SOUND MENU” (see

page 79) is automatically set to “REVERSE”.

Notes

NOTICE

output. 

Loudtesttonesare

 



Pleasekeepquiet

orleavetheroom.

Press[ENTER]

AUTOSETUP



MeasurementStart

in 9seconds

[RETURN]:Cancel

Notes

AUTOSETUP

. RESULT

SP : 3/4/0.1

DIST: 4.50/5.30m

LVL : -9.0/+6.5dB

SET CANCEL

[ ]/[ ]:Up/Down

[ENTER]:Detail

AUTOSETUP



Measurement Complete

Press [ENTER]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha RX-V863 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha RX-V863

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info