Bedienungsanleitung Yamaha S03SL (Seite 42 von 112) (Englisch)

588954

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

Basics Section

9Use the [▲] and [▼] buttons to call up the Part

Mode screen (PAGE 9). Set the parameter to

“norm” (normal)

With settings made in steps 3 to 9 above, you can

now play the strings voice assigned to “P1” (Part 1)

and set to MIDI Receive Channel 1 (RcvCh) — when

you play in the key range of B2 and lower.

)Make the settings for the upper Part (Part 2), in the

same manner as you did in steps 3 to 9.

For Part 2, select a piano Voice, setting the Note

Limit Low to “C3” and the Note Limit High to the

maximum of “G8.” Also set the MIDI Receive

Channel to 1, as you did with Part 1. The piano

Voice of Part 2 sounds when you play keys higher

than C3.

nIn the Edit mode, the selected Part’s Voice is played

back.

nTo avoid situations where the Voices of unused Parts

are suddenly played back, you should set the MIDI

receive channels for unused Parts to “off.”

nThere are many other Part-speciﬁc parameters in the

Multi Edit mode. For details, see page 55.

!Before exiting the Multi Edit mode, store the above

settings to a Multi. For instructions on storing a

Multi, refer to page 69.

Now that you’ve created and stored the Multi, you can

call it up anytime within the Multi play mode — and

play a strings Voice from keys B2 and below, while

playing a piano Voice from keys C3 and above.

Layering Two Voices

(Parts) Together

The illustration below gives one application example of

combining two Voices in a layer. In this example, a

strings Voice is selected for Part 1 and a piano Voice is

selected for Part2, and the two are played together in

unison.

This Multi can be easily created and set so that both

Parts 1 and 2 are layered together across the entire

range of the keyboard.

•For both Part 1 and Part 2, set the Note Limit Low

parameter to “C-2” and the Note Limit High

parameter to “G8.”

nIn the Edit mode, the selected Part’s Voice is played

back.

Saving S03 Settings to an External Device (Bulk Dump Send)

Using the Bulk Dump function, you can transmit

your S03 settings to an external device, such as a

computer, and save them. This is a fast and

convenient way to back up your important data. You

can also use this function to record important S03

data at the beginning of a song, so that all your

original settings and data are automatically reset

when your play back the song.

The following explanation shows you how to do this

using the realtime recording functions of the

sequencer software. In this example, track 1 is used

for recording the User Multi data.

nThe explanations in this section apply in general to

sequencer software and are not speciﬁc to any

particular program or device. The steps in each

procedure may vary slightly, depending on your

particular computer or sequencer software. For

speciﬁc information and operation instructions,

refer to the owner’s manual (or help messages) of

your particular sequencer.

nMake sure that the S03 is properly connected to the

computer (page 13). For information on settings

for your sequencer, refer to the owner’s manual (or

help messages) of your particular sequencer.

Part 1

Part 2

Strings Piano

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha S03SL Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha S03SL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info