Bedienungsanleitung Yamaha S30 (Seite 115 von 156) (Englisch)

586917

115

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

115

Performance Mode

MIX Level

You can set output level, pan, effect send and other

parameters for each Part. This is useful when setting

up the levels of each Part in a mix.

■Vol (Volume)

Set the output level of the Part.

❏Settings: 0 ~ 127

■Pan

Set the stereo pan position of the Part.

❏Settings: L63 (Left) ~ C (Center) ~ R63 (Right)

■RevSend (Reverb Send)

Set the Send level of the signal sent from Insertion

Effect 1/2 (or the bypassed signal) to the Reverb

effect.

❏Settings: 0 ~ 127

■ChoSend (Chorus Send)

Set the Send level of the signal sent from Insertion

Effect 1/2 (or the bypassed signal) to the Chorus

effect.

❏Settings: 0 ~ 127

Part Tone

You can set Filter, Envelope Generator and other

parameters controlling the tonal characteristics of each

Part. The following four screens are available.

TON Filter (Tone Filter)

TON EG (Tone Envelope Generator)

TON Portamento (Tone Portamento)

TON Other (Tone Other)

TON Filter (Tone Filter)

You can use filters to adjust the tone of each Part. If

the filter is an LPF and HPF combination, the Cutoff

parameter applies to the LPF. These parameters are

also available in the Common Quick Edit screens.

Details about the Filter are given on Page 78.

■Cutoff

Raise or lower the Cutoff frequency for each

Element of a Part.

For each Element, if a combined Low Pass and High

Pass Filter is being used, this parameter adjusts the

Cutoff frequency of the Low Pass Filter.

❏Settings: -64 ~ 0 ~ +63

TONíFilter) Cutoff Reso

Part01 +63 +63

MIXíLevel) Vol Pan RevSend ChoSend

Part01 127 C 64 0

■Reso (Resonance)

Set the amount of Resonance (harmonic emphasis)

applied to the signal at the Cutoff frequency. This

adds further character to the sound.

❏Settings: -64 ~ 0 ~ +63

TON EG (Tone Envelope Generator)

You can set EG (Envelope Generator) parameters for

each Part. There are four parameters governing the

transition in output level from the moment a note is

pressed on the keyboard to the moment it is released or

the point at which the output level has faded to zero.

For more information, refer to a diagram that illustrate the

concept of Envelope Generator, which you can find in Voice

Edit Mode sections.

Part 1 to 16

Plug-in Part

Multi Plug-in Part

Drum Voice Part

■Attack

Set the transition time from the moment a key on

the keyboard is pressed to the point at which the

output level of the Part reaches its peak. A positive

value will lengthen the transition time and a

negative value will shorten it.

❏Settings: -64 ~ 0 ~ +63

■Decay

Set the transition time from the point at which the

output level of the Part reaches its peak to the point at

which it levels off. A positive value will lengthen the

transition time and a negative value will shorten it.

❏Settings: -64 ~ 0~ +63

■Sustain

Set the output level of the Part maintained while the

key on the keyboard is being held down.

This parameter is not available for Plug-in or Drum

Voice Parts.

❏Settings: -64 ~ 0 ~ +63

TONíEG) Attack Decay

Part10 + 0 + 0

TONíEG) Attack Decay Release

PartPL + 0 + 0 + 0

TONíEG) Attack Decay Sustain Release

Part01 + 0 + 0 + 0 + 0

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha S30 Seite 115

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha S30

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info