Bedienungsanleitung Yamaha S30 (Seite 127 von 156) (Englisch)

586917

127

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

127

Utility Mode

MSTR (System Master)

You can set the overall parameters, including volume and

pitch, which mainly relate to the synthesizer’s tone

generator section. The following four screens are available.

MSTR TG (Master Tone Generator)

MSTR Kbd (Master Keyboard)

MSTR EF Bypass (Master Effect By-pass)

MSTR Other (Master Other)

MSTR TG (Master Tone Generator)

Set the parameters which control the synthesizer’s tone

generator section.

■Vol (Master Volume)

Set the synthesizer’s overall volume.

❏Settings: 0 ~ 127

■NoteShift (Master Note Shift)

Set the amount (in semitones) by which the note

pitch is shifted. This parameter only affects the

synthesizer’s internal tone generator. It does not

affect information transmitted via MIDI.

❏Settings: -24 ~ 0 ~ +24

■Tune (Master Tune)

Adjust the keyboard tuning (in 0.1 cent steps).

❏Settings: -102.4 ~ +102.3

MSTR Kbd (Master Keyboard)

Set the parameters related to the keyboard.

■Oct (Master Octave Shift)

Shift the octave range of the keyboard up or down.

❏Settings: -3 ~ 0 ~ +3

■Trnspose (Master Transpose)

Transpose the pitch of the keyboard up or down (in

semitones). This affects information transmitted via

MIDI.

❏Settings: -11 ~ +11

If you transpose beyond the note range limits (C-2 and G8), the

notes will be wrapped over.

MSTR Kbd) Oct Trnspose Vel 

Sys +3 +11 fixed = 127

MSTR TG) Vol NoteShift Tune

Sys 127 +24 +102.3c

The parameters in Utility Mode are explained here.

Utility Mode can roughly be divided into a screen for

settings common to the entire system, a screen for Voice

Mode settings and a screen for Plug-in Board settings.

You will first see the following screen when you enter

Utility Mode. Each of the three Utility Mode screens

contain further sub-screens. Basically the [PAGE] knob

is used to switch between parameter screens and Knobs

[B], [C] and [1]/[2] are used to set the values for each

parameter. You can also use the [DATA] knob or the

[DEC/NO] and [INC/YES] keys to enter values.

Sys (System): System settings

• Master

• Control

• MIDI

Vce (Voice): Voice Mode settings

• Master Equalizer

• Control

Plg (Plug-in): Plug-in Settings

• Plug-in Board MIDI

• Plug-in Board System

Details about how to enter Utility Mode are given on

Page 17.

Menu Display

When you use the [PAGE] knob while holding down

the [SHIFT] key, the following menu will be

displayed. Use the [PAGE] knob to move the cursor

(≥) between items, then release the [SHIFT] key to

jump to the selected item.

SHIFT PAGE

PART

ELEMENT

DATAA B C 1 2

MSTR TG) Sys:>MSTR≥CTRL>MIDI 

Sys Vce:>M.EQ>CTRL>PLG

Cursor

PLG MIDI) Clock DevNo

PLG150-AN on all

M.EQ Low) Shape Gain Freq Q

Vce peak +12dB 50Hz 12.0

MSTR TG) Vol NoteShift Tune

Sys 127 +24 +102.3c

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha S30 Seite 127

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha S30

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info