Bedienungsanleitung Yamaha S30 (Seite 138 von 156) (Englisch)

586917

138

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

138

Card Mode

4Press the [INC/YES] key to save the file. The

message “Completed.” will be displayed after it has

been saved, and you will be returned to the previous

screen.

The save operation will be canceled if you press the

[DEC/NO] key during execution.

When saving a file, the “Card full” message will be

displayed if the space left on the Memory Card is

insufficient. Free up space by deleting unwanted data

and so on, then try saving the file again.

If you enter the name of a file that already exists, you

will see the “Overwrite? Are you sure?” confirmation

message before saving.

Take care not to overwrite important data held on

Memory Card.

File Name Settings

The procedure for renaming files is basically the

same as for renaming Voices. However, you cannot

use symbols or lower case characters, and the name

can only be up to eight characters in length. Details

about renaming Voices are given on Page 65.

Files are named according to the MS-DOS naming

convention. If the file name contains spaces and

other characters unrecognized in MS-DOS, these

characters will automatically be replaced by “_”

(underscore) characters when saving.

Load

You can load files from Memory Card to the

synthesizer is as follows.

■Type (File Type)

❏Settings: all (all data), perf (Performance), all-voice, voice,

chain (Sequence Chain), plugin

1Use Knob [B] to select the File Type of the data to be

loaded.

2Use Knob [C] to select the File Number.

3When you press the [ENTER] key, the following will

be displayed, depending on the selected File Type.

Load) Type File:/VOICEDIR/SUBDIR-1/

Card all-voice 001[NEWFILE .S2V]

File Number of

file to be loaded

Data to be loaded

(File Type)

•If you have selected a File Type other than

“perf” or “voice”:

A confirmation message is displayed before loading.

The synthesizer will automatically select an appropriate

location in its internal memory, according to the file type

being loaded.

•If you have selected “perf” or “voice” as the File

Type:

You will further have to specify the type of data and

the location to which the file will be loaded.

Use Knobs [B], [C], [1] and [2] to select the file and

the location to which it will be loaded.

Alternatively, you can use the [DATA] knob and the

[DEC/NO] and [INC/YES] keys.

When you press the [ENTER] key, you will see a

confirmation message.

The types of data that you can select for each File

Type, and the locations to which they will be loaded,

are as follows.

perf (Performance)

❏Settings:

Source Performance Memory:

INT (Internal), EXT (External)

Source Performance Number:

all (all Performances), 1 ~ 128 (INT), 1 ~ 64 (EXT)

Target Performance Memory:

INT (Internal), EXT (External)

Target Performance Number:

all (all Performances), 1 ~ 128 (INT), 1 ~ 64 (EXT)

If you set the source Performance Number to “all,” the

target Performance Number will also be set to “all.”

Load) [Pf:Init Perf ] [Pf:Init Perf ]

Card EXT:064(D16) > INT:128(H16)

Performance Number

of file to be loaded (source)

Performance Number to

which file will be loaded (target)

Performance Memory

of file to be loaded (source) Performance Memory to

which file will be loaded (target)

Load) Type File:/VOICEDIR/SUBDIR-1/

<< Are you sure? [YES]/[NO] >>

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha S30 Seite 138

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha S30

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info