Bedienungsanleitung Yamaha XV920 Virago (Seite 309 von 363) (Englisch)

689861

309

Zoom out

Zoom in

Vorherige Seite

1/363

Nächste Seite

8A-6 Chapter 8 Part A Electrical system (XV535 models)

8.3 The headlight adjusting screws are

located on either side of the headlight

assembly; the vertical adjusting screw is

at the lower right (arrow); the horizontal

adjusting screw is at the upper left

9.2 Remove the pivot bolt and nut at the

bottom (arrows) and the mounting bolt

inside the headlight assembly

10.2 Press the bulb into the socket and

turn it counterclockwise (anti-clockwise

to remove

10.5 Remove the lens screws (arrows) and take off the lens

10.6 Press the bulbs into their sockets and turn counterclockwise

(anti-clockwise) to remove

2 The headlight beam can be adjusted both vertically and

horizontally. Before performing the adjustment, make sure the fuel tank

is at leasi half full and have an assistant sit on the seat.

3 The horizontal adjusting screw is at the upper left of the headlight

cover (see illustration). The vertical adjusting screw is located at the

lower right.

9 Headlight assembly - removal and installation

Refer to illustration 9.2

1 Remove the headlight cover (see Section 7). If you're planning to

take the headlight assembly completely off the motorcycle, disconnect

the electrical connectors inside the headlight assembly. If you're just

removing the assembly for access to the speedometer, the connectors

can be left attached.

2 Remove the mounting bolt inside the headlight cover and the

pivot bolt at the bottom (see illustration). Slide the assembly down

and forward so the mounting grommet can clear the post, then take

the assembly off the motorcycle.

3 Installation is the reverse of the removal steps.

10 Turn signals and tail/brake light bulbs - replacement

Turn signal bulbs

Refer to illustration 10.2

1 To replace a turn signal bulb, remove the screws that hold the

lens to the turn signal housing and take off the lens.

2 Push the bulb in and turn it counterclockwise (anti-clockwise) to

remove it (see illustration).

3 Check the socket terminals for corrosion and clean them if

necessary. Line up the pins on the new bulb with the slots in the

socket, push in and turn the bulb clockwise until it locks in place.

Note: The pins on US model front turn signal bulbs are offset so they

can only be installed one way. It is a good idea to use a paper towel or

dry cloth when handling the new bulb to prevent injury if the bulb

should break and to increase bulb life.

4 Position the lens on the housing and install the screws. Be careful

not to overtighten them or the lens will crack.

Tail/brake light bulbs

Refer to illustrations 10.5 and 10.6

5 Remove the lens screws and take the lens off (see illustration).

6 . Push the bulb in and turn it counterclockwise (anti-clockwise) to

remove it (see illustration).

7 Perform Steps 3 and 4 above to install the bulb, noting that the

pins are offset.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha XV920 Virago Seite 309

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info