Bedienungsanleitung Yamaha YHT-594 (Seite 9 von 12) (Englisch)

554705

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

7 En

English

You can mount the speakers on the wall as follows.

• Surround speakers (NS-B285)

1 Install screws into a solid wall or wall support, as

shown below. Use 3.5 to 4 mm (1/8") diameter self-

tapping screws.

2 Hang each speaker by its keyhole slots onto the

protruding screws.

Note

• Make sure the shaft of the screw is seated in the narrow part

of the keyhole slot. Otherwise, the speaker may fall.

• Front/center speaker (NS-BR300)

1 Use tape or thumbtacks to affix the supplied

mounting template to the wall, and use a pencil or

other tool to mark the hole positions on the wall.

2 Remove the template, and then install screws, as

shown below. Use 3.5 to 4 mm (1/8") diameter self-

tapping screws.

3 Hang the speaker by its keyhole slots onto the

protruding screws.

Note

• Make sure the shaft of each screw is seated in the narrow

part of each keyhole slot. Otherwise, the speaker may fall.

Cautions

• The front/center speaker (NS-BR300) weighs 1.5 kg

(3 lbs.). The surround speakers (NS-B285) weigh 0.45 kg

(1 lbs.). Do not mount the speakers on thin plywood or on

walls with a soft surface material. Otherwise, the screws

may pull out of the surface and the speakers may fall,

causing damage or injury.

• Do not affix the speakers to walls by using nails,

adhesives, or unsuitable hardware. Long-term use and

vibration may cause the speakers to fall.

• To prevent tripping accidents, secure loose speaker cables

to walls, floors, etc., using suitable fasteners.

• Mount the speakers at positions on the walls where

people are unlikely to bump their heads.

• Attach the speakers to a rack or wall. Do not attach the

speakers to walls made of weak materials, such as plaster

or veneered woods. Doing so may cause the speakers to

fall.

• Use commercially available screws that can support the

weight of the speakers.

• Only use the screws specified for attaching the speakers.

Using fasteners other than those specified, such as short

screws, nails, or double-sided tape, may cause the

speakers to fall.

• When connecting the speakers, secure the speaker cables

so that they do not hang loose. If your foot or hand

accidentally gets caught on a loose speaker cable, the

speaker may fall, causing damage or injury.

• After installing each speaker, check that it’s fixed securely.

Yamaha accepts no responsibility whatsoever for

accidents due to improper installation.

Wall-mounting the speakers

Unless you are very competent at DIY, do not wall-mount the

speaker yourself. Ask your dealer or a qualified contractor to

do the installation for you. Incorrect installation may cause

the speaker to fall, causing damage or injury.

45 mm

(1-3/4")

Wall/wall

support

6 mm

(1/4")

Minimum

20 mm (3/4")

NS-B285

Tape or

thumbtacks

Mark

here

Mounting

template

4 to 6 mm (3/16" to 1/4")

Diameter:

7 to 9 mm or more (#8,

1/4" to 3/8" or more)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha YHT-594 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha YHT-594

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info