Bedienungsanleitung Yamaha YSP-3300 (Seite 25 von 82) (Englisch)

516956

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

Initial settings

25 En

PREPARATION PLAYBACK SETTINGS

TROUBLESHOOTING

APPENDIX

The screen below is displayed after connecting

IntelliBeam microphone to the unit.

Press the ENTER key to start the AUTO

SETUP procedure and then leave the room

within 10 seconds.

The screen automatically changes during the AUTO

SETUP procedure.

If the AUTO SETUP procedure is complete, this unit

rings the chimes.

AUTO SETUP

(PREPARATION & CHECK)

Please connect the MIC.

Please place the MIC at least

1.8m/6ft away from Sound Pro-

jector. The MIC should be set

at ear level when seated.

Measurement takes about 3min.

After [ENTER] is pressed,

please leave the room.

[ENTER]:Start [RETURN]:Cancel

Follow the instructions below and then leave the room. If you remain

in the room, you may obstruct the beam, or the microphone may pick

up any sounds you make, possibly resulting in improper

configuration of settings.

Note

ENVIRONMENT CHECK: Success

BEAM MODE: 5Beam/Plus2

SHOW RESULT

MESUREMENT COMPLETE.

[ENTER]:Save set-up.

[RETURN]:Do not save set-up.

Will begin in 10 sec.

Please leave the room

----------

AUTO SETUP START

[RETURN]:Cancel

(After 3 min.)

Press the ENTER key to confirm the

results.

Measurement results are applied to this unit.

• The measurement results are stored in the internal

memory of this unit until you run the AUTO SETUP

procedure again or configure the settings manually.

• You can save the several measurement results pressing

the SYSTEM MEMORY key (☞p. 28).

Remove the IntelliBeam microphone.

The “AUTO SETUP COMPLETE” screen closes.

Keep the IntelliBeam microphone in a safe place.

AUTO SETUP COMPLETE

Please remove the MIC

from Sound Projector

and the listening position.

Press [SYSTEM MEMORY] key

to save set-up in the memory.

“BEAM+SOUND OPTIMIZE” is selected automatically. When you

perform “BEAM OPTIMIZE ONLY” or “SOUND OPTIMIZE ONLY”

only, refer to “AUTO SETUP via setup menu” (☞p. 26).

• Wait outside the room during the AUTO SETUP procedure.

Remaining in the room after the AUTO SETUP process begins may

result in the improper configuration of settings as your body may

obstruct sound beams or the microphone may pick up sounds you

make inadvertently.

• The AUTO SETUP procedure takes about 3 minutes.

• To cancel the AUTO SETUP procedure after it is started, press the

RETURN key.

If an error occurs, an error buzzer sounds and an error message is

displayed. For details on error messages, see “If an error message is

displayed” (☞p. 27).

• If “ENVIRONMENT CHECK:Failure” is displayed, accurate

measurement may not have been possible. See “ERROR-E1” under

“Error messages” (☞p. 27) for the remedy to this most common error.

Press the RETURN key and begin measurement again.

• Depending on the environment of your listening room, the front left

and right beam angles and left and right surround beam angles may be

set to the same value even if “BEAM MODE :5Beam” is displayed as

a result.

If you do not want to apply the results, press RETURN key.

When AUTO SETUP is performed from the setup menu, the menu

selection screen of the setup menu appears.

1) y

2) y

3) y

4) y

5) y

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha YSP-3300 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha YSP-3300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info