Bedienungsanleitung Yamaha YSP-3300 (Seite 31 von 82) (Englisch)

516956

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

Initial settings

31 En

PREPARATION PLAYBACK SETTINGS

TROUBLESHOOTING

APPENDIX

When the connected components and jacks are changed, reset this

unit with the following procedure.

Setting the HDMI control function

Turn on all components connected to this

unit via HDMI cable.

Enable the HDMI control function of all

components connected to this unit via

HDMI cable.

For this unit, set “HDMI CONTROL” to “ON” (☞p. 65).

For external components, refer to the manual supplied

with each component.

Turn off the TV and then turn on it again.

Registering HDMI compatible

components to the TV

Select this unit as the input source of the

TV.

Turn on an external components, such as

a Blu-ray disc player, connected to this

unit via HDMI cable.

Select the input source of this unit to

Blu-ray disc player and check whether the

image in the player is correctly displayed

or not.

If the Blu-ray disc player is connected via HDMI IN1

jack, press the HDMI1 key.

Check if the HDMI control function works

(turn on this unit or adjust the volume level

using the remote control of the TV).

HDMI1

Input source name

If the HDMI control function is not working

Be sure that all components are correctly connected to this

unit, and that settings are properly configured as described

below.

– The TV is connected to the HDMI OUT (ARC) jack of this

unit.

– “HDMI CONTROL” (☞p. 65) is set to “ON” in the setup

menu.

– The HDMI control function is enabled on the TV. (Also

check the relative settings such as power interlock function

or speaker priority.)

When the HDMI control function is not still working even

after the above has been checked,

– Turn off this unit and the TV, and then turn them back on

again.

– Disconnect the AC power supply cable of the unit and

external components connected to the unit via HDMI cable.

Plug them in again after about 30 seconds.

– After OPTICAL, ANALOG, AUX, YIT, or USB

input

has been enabled, switch the input source for the TV and

this unit to the components connected via HDMI cable.

Changing the connection method and

connected components

Disable the HDMI control function of the

TV and Blu-ray disc player, turn off all

connected components, and change the

connections.

Perform steps 1 to 3 of “Setting the HDMI

control function”.

• The default setting is “OFF”.

• When “HDMI CONTROL” is set to “ON”

When the Eco function (☞p. 41) is enabled, this unit enters standby

mode if the TV is selected for audio output using the TV’s remote

control.

The example of TV settings

• From the setup menu on your TV, select “Link setting”  “HDMI

control setting”, then set a setting such as “HDMI control function” to

“ON”.

• Setting such as “Speaker priority” should be set to “AV amplifier”.

For some HDMI compatible components, registering HDMI compatible

components to TV is not required in this case when the HDMI control

function is enabled.

YSP-4300 only

2) y

3) y

4) y

5) y

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha YSP-3300 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha YSP-3300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info