Bedienungsanleitung Yamaha ysp 4100 (Seite 40 von 54) (Englisch)

419747

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

40 En

APPENDIX

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction

below does not help, set this unit to the standby mode, disconnect the AC power supply cable, and contact the nearest authorized Yamaha dealer

or service center.

■ General

Troubleshooting

Problem Cause Remedy

See

page

This unit does not operate

properly.

The internal microcomputer has been frozen by an

external electric shock (such as lightning or excessive

static electricity) or by a power supply with low

voltage.

Disconnect the AC power supply cable from the

outlet and plug it in again after about 30 seconds.

This unit fails to turn on when

CPower (p) key is pressed, or

enters the standby mode soon

after the power has been turned

on.

The AC power supply cable is not firmly connected to

the AC wall outlet.

Connect the AC power supply cable firmly to the AC

wall outlet.

This unit has been exposed to a strong external

electric shock (such as lightning and strong static

electricity).

Set this unit to the standby mode, disconnect the AC

power supply cable, plug it back in after 30 seconds,

and use it normally.

This unit suddenly enters the

standby mode.

The internal temperature becomes too high and the

overheat protection circuitry has been activated.

Wait for about one hour for this unit to cool down and

turn it back on.

—

The sleep timer has turned the unit off. Turn on the power and play back the source again. 21

No sound. Incorrect input or output cable connections. Connect the cables properly. If the problem persists,

the cables may be defective.

No appropriate input source has been selected. Select an appropriate input source with INPUT or

DInput selector keys.

The volume is turned down. Turn up the volume. 21

The sound is muted. Press KMUTE or KVOLUME +/– to resume audio

output and adjust the volume level.

The signals this unit cannot reproduce (such as PCM

signals with more than 96 kHz of sampling

frequency) are being received from the source

component.

Play a source whose signals can be reproduced by this

unit.

—

Change the system settings of the source component. —

The HDMI components connected to this unit do not

support the HDCP copy protection standards.

Connect the HDMI components that support the

HDCP copy protection standards.

“SUPPORT AUDIO” is set to “OTHER” and HDMI

audio signals are not being played back on this unit.

Set “SUPPORT AUDIO” to this unit in “SET

MENU”.

No sound or too small sound from

a specific channel

The output level of the channel is muted. Raise the output level of the channel.

The beam setting is inappropriate. Adjust the beam setting.

You play back the source in the stereo mode. Start surround playback. 22

Some audio output methods do not output sound

beams for certain channels.

Select another beam mode.

No sound from the subwoofer. “BASS OUT” is set to “FRONT OR AUTO” in

“SUBWOOFER SET”.

Set “BASS OUT” to “SUBWOOFER” in

“SUBWOOFER SET”.

The source does not contain low bass signals.

No sound from the subwoofer

connected by wireless.

The group IDs of this unit and SWK-W10 are not set

to the same value.

Check whether the group IDs of this unit and SWK-

W10 are set to the same value.

“Wireless Function” is set to “No”. Set “Wireless Function” to “Yes”.

Distorted or too little bass sound. “CROSS OVER” is set incorrectly in

“SUBWOOFER SET”.

Set “CROSS OVER” correctly in “SUBWOOFER

SET”.

Surround sound effects are

insubstantial.

The listening room is not a regular shape. Install this unit in a square or rectangular shaped

room.

—

There is no wall in the path of the sound beam. Try placing a flat object, such as a board, in the path

of the sound beam.

—

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha ysp 4100 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yamaha ysp 4100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info