Bedienungsanleitung Yard Machines TRACTOR 42SD 1650S 5STY - 13AN775S000 (Seite 22 von 68) (Englisch)

522631

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

4. Retighten the jam nut loosened earlier when proper

adjustment is achieved.

Side to Side

If the cutting deck appears to be mowing unevenly, a side to side

adjustment can be performed. Adjust if necessary as follows:

1. With the tractor parked on a firm, level surface, place the

deck lift lever in the second from the top notch (second

highest position) and rotate both blades so that they are

perpendicular with the tractor.

2. Measure the distance from the outside of the left blade

tip to the ground and the distance from the outside of the

right blade tip to the ground. Both measurements taken

should be equal. If they’re not, proceed to the next step.

3. Loosen, but do NOT remove, the hex cap screw on the left

deck hanger bracket. See Figure 6-5.

Hex Cap Screw

Figure 6-5

4. Balance the deck by using a wrench to turn the adjustment

gear (found immediately behind the hex cap screw just

loosened) clockwise/up or counterclockwise/down.

The deck is properly balanced when both blade tip

measurements taken earlier are equal.

5. Retighten the hex cap screw on the left deck hanger

bracket when proper adjustment is achieved.

Seat Adjustment

Refer to the Set-Up and Assembly section of this manual for seat

adjustment instructions.

Parking Brake Adjustment

WARNING! Never attempt to adjust the brakes

while the engine is running. Always disengage PTO,

move shift lever into neutral position, stop engine

and remove key to prevent unintended starting.

If the tractor does not come to a complete stop when the brake

pedal is completely depressed, or if the tractor’s rear wheels

can roll with the parking brake applied, the brake is in need of

adjustment. See an authorized MTD Service Dealer to have your

brakes properly adjusted.

12. On 46” decks, repeat steps 4 through 11 on the opposite

side of the cutting deck.

IMPORTANT: After cleaning your deck with the Deck Wash

System™ , return to the operator’s position and engage the PTO.

Keep the cutting deck running for a minimum of two minutes,

allowing the underside of the cutting deck to thoroughly dry.

Adjustments

WARNING! Never attempt to make any

adjustments while the engine is running, except

where specified in the operator’s manual.

Leveling the Deck

NOTE: Check the tractor’s tire pressure before performing any

deck leveling adjustments. Refer to Tires in the Service section of

this manual for more information regarding tire pressure.

Front To Rear

The front of the cutting deck is supported by a stabilizer bar that

can be adjusted to level the deck from front to rear. The front of

the deck should be between ¼-inch and ⁄-inch lower than the

rear of the deck. Adjust if necessary as follows:

1. With the tractor parked on a firm, level surface, place the

lever for lifting the platform on the second to the top notch

(second highest position) and rotate the blade as close to

the discharge channel that is parallel to the tractor.

2. Measure the distance from the front of the blade tip to

the ground and the rear of the blade tip to the ground.

The first measurement taken should be between ¼” and

⁄” less than the second measurement. Determine the

approximate distance necessary for proper adjustment and

proceed, if necessary, to the next step.

3. On some models: Locate the jam nut and lock nut on

the front side of the stabilizer bracket. Others have just a

flange nut as seen in Figure 6-4.

Figure 6-4

After loosening the jam nut (on some models):

•

Tighten the lock nut to raise the front of the deck;

• Loosen the lock nut to lower the front of the deck.

22 Section 6— Maintenance & adjuStMentS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yard Machines TRACTOR 42SD 1650S 5STY - 13AN775S000 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info