Bedienungsanleitung Yard Machines TRACTOR 42SD 1650S 5STY - 13AN775S000 (Seite 21 von 68) (Englisch)

522631

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Cleaning Battery

Clean the battery by removing it from the tractor and washing

with a baking soda and water solution. If necessary, scrape the

battery terminals with a wire brush to remove deposits. Coat

terminals and exposed wiring with grease or petroleum jelly to

prevent corrosion.

Battery Failures

Some common causes for battery failure are:

• Incorrect initial activation

• Overcharging

• Freezing

• Undercharging

• Corroded connections

These failures are NOT covered by your tractor’s warranty.

Cleaning the Engine And Deck

Any fuel or oil spilled on the machine should be wiped off

promptly. Do NOT allow debris to accumulate around the cooling

fins of the engine or on any other part of the machine.

IMPORTANT: The use of a pressure washer to clean your

tractor is NOT recommended. It may cause damage to electrical

components, spindles, pulleys, bearings or the engine.

On some decks, a hex plug can be found on your tractor’s deck

surface as seen in Figure 6-2. Or on some units there could be a 1/4”

screw holding in a plug. On either configuration, this plug can be

replaced with a water port to be used as part of a separately-

available deck wash system.

Hex Plug

Figure 6-2

The Deck Wash System™ is used to rinse grass clippings from the

deck’s underside and prevent the buildup of corrosive chemicals.

NOTE: Refer to the Attachments & Accessories section of this

manual for information regarding this and other separately-

available attachments & accessories for your tractor.

Deck Wash System™

If your tractor’s deck is equipped with a water port on its surface

as part of its Deck Wash System™, follow these instructions to

utilize this feature.

Use the Deck Wash System™ to rinse grass clippings from the

deck’s underside and prevent the buildup of corrosive chemicals.

Complete the following steps AFTER EACH MOWING:

1. Drive the tractor to a level, clear spot on your lawn, near

enough for your garden hose to reach.

CAUTION: Make certain the tractor’s discharge

chute is directed AWAY from your house, garage,

parked cars, etc.

2. Disengage the PTO (Blade Engage), set the parking brake

and stop the engine.

3. Thread the hose coupler (packaged with your tractor’s

Operator’s Manual) onto the end of your garden hose.

4. Attach the hose coupler to the water port on the deck’s

surface. See Figure 6-3.

Figure 6-3

5. Turn the water on.

6. While sitting in the operator’s position on the tractor, start

the engine and place the throttle lever in the FAST (rabbit)

position.

7. Move the tractor’s PTO (Blade Engage) into the ON position.

8. Remain in the operator’s position with the cutting deck

engaged for a minimum of two minutes, allowing the

underside of the cutting deck to thoroughly rinse.

9. Move the tractor’s PTO (Blade Engage) into the OFF

position.

10. Turn the ignition key to the STOP position to turn the

tractor’s engine off.

11. Turn the water off and detach the hose coupler from the

water port on your deck’s surface.

21Section 6 — Maintenance & adjuStMentS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yard Machines TRACTOR 42SD 1650S 5STY - 13AN775S000 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info