Bedienungsanleitung Yardforce NX 80i (Seite 10 von 12) (Englisch)

779823

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

16 17

GB GB

Maintenance and storage

Maintenance work that has not been described in these instructions must be carried out by a

servicing agency authorised by the manufacturer. Only use original parts.

Maintenance

Check and clean your Robotic Mower regularly and replace worn parts if necessary. Preferably

use a dry brush, a damp cloth or a sharpened wooden piece.

Never use flushing water.

Following these maintenance instructions can extend your Robotic Mower's service life.

Battery Life

The Robotic Mower has a maintenance free Li-ion battery, with an estimated life of more than 2

years (depending on treatment and usage).

Winter Storage

During winter, keep your mower, docking station and power supply in a dry place.

We recommend a shed, garage or preferably store it indoors.

Prepare your device for winter storage as follows:

1. Fully recharge the battery.

2. Set the mains power switch to "OFF".

3. Thoroughly clean your Robotic Mower.

4. Unplug the power supply from the mains outlet.

5. Disconnect the power supply from the docking station.

6. Disconnect the boundary wire from the docking station. Lift up the docking station and clean.

The boundary wire can remain outside. However, it is imperative to protect the wire against

corrosion. We recommend a water-free grease or suitable sealing tape.

If available, repack the product in the original packaging.

Alternatively, our service centre offers a winter service for your device. This will include a check-up

of all parts and - if available - a software upgrade.

Preparing for spring

After winter storage, please clean the charging contacts on both the Robotic Mower and the

docking station.

Use a fine abrasion paper or a brass brush; this will help to achieve the best charging efficiency

and avoid any charging interference.

Cleaning the mower body

As your Robotic Mower is battery powered you need take care when cleaning. Remove rough dirt

with a soft brush. Use a manual water spray with mild household detergent for intensive cleaning.

Wipe off any residue after cleaning with a moist rag.

Disposal

To help the environment, please dispose of the product properly when it has reached the end of

its useful life and not in the household waste. Information on collection points and their opening

hours can be obtained from your local authority.

Li-Ion environmental damage through incorrect disposal of the batteries / rechargeable batteries.

Remove the battery pack from the product before disposal. Batteries /rechargeable batteries may

not be disposed of with the usual domestic waste. They may contain toxic heavy metals and are

subject to hazardous waste treatment rules and regulations. Please dispose of batteries according

to the relevant local requirements.

Replacing the battery

While the actual battery life will depend on usage and environmental factors, the typical service

life is several years. Spare batteries are available from customer support. To replace the battery,

please follow the instructions below.

1. Ensure the main power switch is turned OFF. Clean the underside as instructed.

2. Set the Autonomous Mower to the lowest cutting height.

3. Turn the mower upside-down. Remove the 5 screws fixing the battery compartment's lid.

Note one screw is partially covered by the blade protector and is only accessible through a

service hole.

4. Pull out the battery and disconnect it from the Autonomous Mower.

5. Carefully clean the lid and the edge of the battery compartment. Debris may allow excessive

water to enter the battery compartment, causing major damage to the appliance.

6. Connect and insert the replacement battery, close the compartment and fix the lid with 5

screws. Do not turn on the Autonomous Mower before placing it back on its wheels. Beware

of sharp blades!

Cleaning the underside

Ensure the main power switch is in OFF position. Wearing protective gloves, turn the Robotic

Mower onto its side to expose its underside. Clean the blade disc and frame using a soft brush or

damp cloth. Rotate the blade disc to make sure that it can move freely, check that the blades can

turn on their pivots and that there is no grass is obstructing them.

Clean the contact pins and the charging strips

Using wire wool, metal cleaner or very fine grade emery paper, clean the contact pins and the

charging strips on your mower and docking station. Remove any debris, leaves, or grass clippings

around the contact pins and charging strips to ensure efficient charging.

OOFFFF

OONN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yardforce NX 80i Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info