Bedienungsanleitung Yardforce NX 80i (Seite 11 von 12) (Englisch)

779823

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

18 19

GB GB

Reversing or replacing the blades

WARNING!

Ensure the Robotic Mower is completely shut off before cleaning, adjusting or

replacing the blades. Always wear protective gloves.

WARNING!

To ensure maximum cutting efficiency and safety, always use recommended

replacement blades and blade mounting parts when replacing.

Your Robotic Mower has three blades, fixed to the blades disk.

Unless damaged by hard obstacles, these blades can last for up to five months of everyday use.

Weekly inspection of the blades and the fixing screws is advised. Note that the blades are double-

edged. When the first side becomes blunt, loosen the fixing screw and the blade upside down and

re-fix. Check that the blade can move freely.

A set of spare blades is included with the Robotic Mower. More blades can be purchased via

customer support.

To ensure you get the best performance from your machine, always replace all three blades at the

same time. Only use spare parts recommended by manufacturer.

NOTE: if blades have been removed/ changed, please ensure that the screw is firmly

secured in place and that the blade is free to move

Spare parts list

In case you need spare parts or any support with your device, please call our after sales centre.

Troubleshooting

Robotic Mower cannot dock with docking station

• Check that the boundary wire in front and underneath the charger is in a straight line.

• Check that the docking station's position is suitable as explained in this manual.

Robotic Mower runs in circles while mowing or while following

boundary wire back to docking station

• Verify that no power cable runs parallel and in close proximity the boundary wire. If necessary,

reposition the boundary wire.

• Check if a front wheel is stuck.

• If a neighbor has a similar Robotic Mower, the signals may interfere. Try setting your docking

station and Robotic Mower are set to the alternative boundary signal S1 to S2.

• Driving motor may be damaged, please contact customer support.

The Robotic Mower is noisy

• Inspect the blade fixing screws; tighten if necessary.

• Inspect the blades for damage; replace if necessary.

• Grass may be too high. Try increasing the cutting height, or mow the lawn with an ordinary

lawnmower first.

• Cutting motor failure, please call after sales service.

Mower remains at or returns to docking station when pressing START

button

• Check if the mower has already completed the programmed working time for that day.

• Battery is low, the Robotic Mower needs to be charged.

LED signal indicator on docking station

S1/S2 indicator lights on.

Boundary wire signal in good condition.

S1/S2 indicator flashes.

Boundary wire broken, no signal.

S1/S2 indicator flashing alternately.

Mower is charging in the docking station.

S1 S2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yardforce NX 80i Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info