Bedienungsanleitung Yardforce Y0GWC3200R0 (Seite 9 von 31) (Englisch)

734892

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

NOTICE:

ALWAYS apply a small amount of lubricant on

o-rings prior to assembling the garden hose to the pump (C),

high pressure hose (D), spray gun (E), and spray wand (F).

Lubricate all connections shown below, following these

instructions:

1) Inspect and clean connecting surfaces prior to lubrication

and assembly.

2) Use lubricants sparingly during assembly; a light lm is

all that is required.

3) Use a small brush or cotton swab to apply grease directly

to o-rings where they are not accessible(QC tting, M22

tting).

6.Connect Hose and Water Supply to Pump

IMPORTANT! DO NOT run the pump without the water

supply connected and turned on.

• Damage to pressure washer resulting from failure to follow

this instruction will void warranty.

NOTICE:

Remove and discard the shipping caps from the

pump’s high pressure outlet and water inlet before attaching

hoses.

1) Uncoil high pressure hose when handle folded, and

attach one end of hose to the base of the spray gun.

Tighten by hand. The other end already assembled to

the pump at the factory.

NOTICE:

The hose only can be uncoiled from the bottom of

the hose reel, it’s recommended to keep the handle folded

for easy unwinding and winding the hose.

WARNING! The high pressure stream of water that the

pressure washer produces could cut through skin

and its underlying tissues, resulting in serious

injury and possible amputation.

• NEVER connect high pressure hose to spray wand.

• Keep high pressure hose connected to pump and spray

gun while system is pressurized.

• Always be certain spray gun, wand, nozzles and other

accessories are correctly attached.

2) Before you connect your garden hose to the water inlet,

inspect the inlet screen. Clean the screen if it contains

debris or have it replaced if damaged. Do Not run

the pressure washer if the inlet screen is damaged or

missing.

IMPORTANT! NEVER siphon standing water for the water

supply. Use only cold water (less than 100 °F).

CAUTION! Using a One Way Valve (vacuum breaker

or check valve) at pump inlet could cause pump or inlet

connector damage.

1) There must be at least 10 ft. (3 m) of unrestricted garden

hose between pressure washer inlet and any device,

such as a vacuum breaker or check valve.

2) Damage to pressure washer resulting from failure to

follow this instruction will void warranty.

3) Run water through garden hose for 30 seconds to ush it

of debris. Turn o water.

4) Connect garden hose (not to exceed 50 ft. in length) to

water inlet. Tighten by hand.

WARNING! Risk of eye injury!

Spray could splash back or propel objects resulting

in serious injure.

• Always wear indirect vented (chemical splash) safety

goggles marked to comply with ANSI Z87.1 when using

or in vicinity of the pressure washer.

• NEVER substitute safety glasses or dry-condition

goggles for indirect vented safety goggles.

Inspect inlet screen. Do Not use if

damaged, clean if dirty

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yardforce Y0GWC3200R0 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info