Bedienungsanleitung Yuneec Tornado CGO4 (Seite 8 von 29) (Englisch)

633004

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

ATTACHING CGO4 GIMBAL CAMERA TO MULTICOPTER

NOTICE: Remove the fixed foam pad from the CG04 gimbal camera before proceeding.

STEP 1 Insert the gimbal connection cord to the inner side of gimbal damping plate

(relative to the direction of H920 power connection port).

STEP 2 Mount the gimbal thumb screws and lock washers (4 pcs) to the gimbal and rotate

the screws until they’re secured into the gimbal damping plate.

NOTICE: The front of the gimbal should be installed in the direction of the nose of H920.

NOTICE: Use the dedicated lock washers when rotating

the screws.

STEP 3 Connect the gimbal power cord to H920 power

connection port.

BINDING CGO4 GIMBAL CAMERA TO THE ST24 (SINGLE MODE)

NOTICE: The build number of ST24 should be b94 or above. The user can view the build

number in the ‘About Device’ column.

STEP 1: Power on the ST24, press [ ] button to go to the main interface. Choose FPV, and

enter Model Select.

STEP 2: The default Model type is Multi-copter. Tap the “H920 CGO4” icon and press OK to

enter the flight control interface.

NOTE: The pre-set model in the “Model Select” interface cannot be deleted.

NOTE: The pre-set model can only be bound to one multi-copter. If the user wants to bind to

the other copters, press and hold the “H920 CGO4” icon, select “copy” on the pop-up menu.

Wait for a few seconds and then tap the newly created

icon. Press OK to enter the flight control interface.

STEP 3: Switch on the TORNADO H920. Wait for a

moment until the H920 Main LED indicator blinks blue,

the CGO4 LED indicator blinks green and then start the

binding procedures.

STEP 4: Lean the H920 in the forward direction twice (45°),

until the Main LED indicator blinks yellow.

STEP 5: Tap’System Settings’ and then tap ‘Bind’ on the left side of the screen.

STEP 6: Tap the Refresh icon, and the codes of the H920 and CGO4 will be shown on screen.

CAMERA CONTROL ON MULTICOPTRER (SINGLE MODE)

CAUTION: The gimbal can only be controlled through ST24 When being attached to H920.

Gimbal Pitch Control

There is a gimbal pitch mode switch on ST24---S1. When the switch is in up/middle position,

the CGO4 gimbal camera is in Angle Mode. Use the slider on the left side of the ST24 to set

the pitch/tilt position of the gimbal camera. When the S1 is in bottom position, the gimbal

camera is in Velocity Mode. When the slider is in the middle position, it means the velocity

rate is 0 for the CGO4 gimbal camera, and it will stop pitching up/down. When the slider is

above the middle position, the CGO4 will start pitching up. When the slider is below the

middle position, the CGO4 will start pitching down. The distance between the slider and the

middle position decides the velocity rate, the further distance, the higher velocity it would be.

Choose the right codes and press Bind.

STEP 7

: If it is the first time to bind your CGO4 to the ST24, you need to insert the password:

1234567890. Press OK on the pop-up window to continue.

STEP 8: Press Camera Select and choose CGO4. Press Select, then press OK.

NOTICE: We recommend users to power on the aircraft in the angle mode.

NOTICE: When returns back to the FPV interface, you will hear two long beeps. That means

the binding is complete. The Real-time images can now be seen on the screen.

Button A = Take Still Photo

Button B = Start/Stop Recording Video

Gimbal Yaw Control

There is a gimbal yaw mode switch on ST24---S2.

When the switch position is up and middle, the

gimbal camera is in Follow Mode. The yaw control of

the gimbal camera is now disabled. The gimbal

camera will adjust its yaw direction according to the

aircraft’s movements. When the switch position is

down, the gimbal camera is in Global Mode. The

Gimbal Yaw control knob (K1) is now activated.

When the user rotates the knob in the right direction,

the gimbal camera will rotate to the right side, and

vice versa.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yuneec Tornado CGO4 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yuneec Tornado CGO4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info