Bedienungsanleitung Zanussi ta 850 (Seite 2 von 8) (Englisch)

314889

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

3. INSTALLATION

3.1. Unpacking

Packing used to protect internal parts of the washing

machine during transport must be removed before the

washing machine is put into service for the first time.

Remove all packing from the

washing machine. Tilt the washing

machine sideways and then remove

the packing under the motor, and

straighten the washing machine.

Tilt the washing machine back-

wards, rotate it by a quarter of a turn

on one of its corner to remove the

transport base.

Open the washing machine lid and

remove the immobilization packing

and plastic films.

Close the lid.

Use a 10 mm spanner to remove the

two screws and spacers at the back.

You can now see the openings that

must be closed with the caches in the

pack attached to the washing machi-

ne; do not forget to fold down the

central capsule.

Make sure that you have removed all

these parts from your washing ma-

chine and keep them so that you can

use them again if you need them for

future transport.

If you want to keep your washing ma-

chine aligned with the adjacent furni-

ture, you can cut the pipe support

strip at the back of your washing ma-

chine. Leave the two side closers in

place.

3.2. Position

Put the washing machine on a flat hard floor in a well venti-

lated room. Make sure that your washing machine does not

touch the wall or any other furniture in the room.

3.3. Moving your washing machine

If you want to move your washing

machine, lift it onto its rollers by pul-

ling the lever at the bottom of the

washing machine all the way to the

left. When you have put your

washing machine into the required

location, put the lever back into its

initial position.

3.4. Leveling

Precise leveling will prevent vibrations, noise and move-

ments of the washing machine during operation.

Make the washing machine level by

adjusting the leveling screw that is

too short.

Unscrew the stand and locking col-

lar assembly (lift the washing machi-

ne if necessary).

When the washing machine is sta-

ble, maintain the stand on the

ground and turn the locking collar as

far as posible.

3.5. Water inlet

Screw the supply ppe connector

onto the water inlet tap (20x27 mm),

remembering to use the washer pro-

vided with the washing machine.

Open the water inlet tap.

You cannot prolong the water inlet

pipe. If it is too short, buy a longer

pipe provided for this purpose.

3.6. Drain

The drain siphon must be placed in-

side a drain pipe (or in a washbasin)

at a height of between 70 and 100

cm. Make sure that it cannot fall.

•Important: the drain pipe must

never be prolonged. If it is too short,

call a professional.

3.7. Electrical connection

You can only connect this washing machine to 230 V single

phase power supply.

Check rating of the fuse line: 10 A at 230V.

The washing machine must not be connected through an

extension cable or a power bar.

Check that the earthing connection is conform with the regu-

lations in force.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ta 850 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info