Bedienungsanleitung Zanussi ZDF4010 (Seite 11 von 52) (Englisch, Französisch, Spanisch)

626613

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Activate or deactivate the multitab function before

the start of a washing programme.

You cannot activate or deactivate the multitab function

when the programme operates. Cancel the washing pro-

gramme, then set the programme again.

To activate the multitab function:

• Press and hold the two multitab buttons (function but-

tons D and E). The multitab indicator light comes on.

To deactivate the multitab function:

• Press and hold the two multitab buttons (function but-

tons D and E). The multitab indicator light goes off.

Do these steps if the drying results are not satis-

factory:

1. Fill the rinse aid dispenser with rinse aid.

2. Activate the rinse aid dispenser.

3. Set the rinse aid dosage to position 2.

• You can only activate or deactivate the rinse aid dis-

penser when the multitab function is activated.

To activate/deactivate the rinse aid dispenser:

1. Switch on the appliance.

2. Make sure that the appliance is in setting mode.

3. Press and hold function buttons B and C.

– The indicator lights for function buttons A, B,

and C start to flash.

4. Release function buttons B and C.

5. Press function button B.

– The indicator lights for function buttons A and C

go off.

– The indicator light for function button B contin-

ues to flash.

– The digital display shows the setting.

Rinse aid dispenser deac-

tivated

Rinse aid dispenser activa-

ted

6. Press function button B again.

– The digital display shows the new setting.

7. Switch off the appliance to save the operation.

To use normal detergent again:

1. Deactivate the multitab function.

2. Fill the salt container and rinse aid dispenser.

3. Adjust the water hardness setting to the highest level.

4. Do a washing programme without dishes.

5. Adjust the water softener to the water hardness in

your area.

6. Adjust the rinse aid dosage.

Setting and starting a washing programme

Set the washing programme with the door ajar.

The washing programme only starts after you

close the door. Until then it is possible to modify the set-

tings.

Do these steps to set and start a washing programme:

1. Switch on the appliance.

2. Make sure that the appliance is in setting mode.

3. Press one of the programme buttons. Refer to the

chapter 'Washing programmes'.

– The programme indicator light comes on.

– All other programme indicator lights go off.

– The digital display shows in flashing the pro-

gramme duration.

– The programme-in-progress indicator light

comes on.

4. Close the door.

– The washing programme starts automatically.

– The programme-in-progress indicator light re-

mains on.

When the washing programme operates, you can-

not change the programme. Cancel the washing

programme.

You can select the washing programme and delay

start also with the door closed. When you press a

programme button you have only 3 seconds to select a

different washing programme or a delay start. After

these 3 seconds, the selected programme starts automat-

ically.

Warning! Only interrupt or cancel a washing

programme if necessary.

Caution! Open the door carefully. Hot steam can

come free.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZDF4010 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZDF4010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info