Bedienungsanleitung Zelmer 13Z011 (Seite 225 von 228) (Englisch, Polnisch)

538892

225

Zoom out

Zoom in

Vorherige Seite

1/228

Nächste Seite

225

16.10. Restoring factory settings

When the appliance is ready to use the message READY TO BREW appears on the display. To delete all settings made by

the user and to restore factory settings proceed according to the algorithm below.

ATTENTION! The language setting procedure is presented in section 16.2.

17. Warnings

The message a. MEASUREMENT ERROR TEMP. indicates that the temperature inside the coffee maker is too low (be-

low 2°C). If this message appears when the room temperature is above 2°C, it means that there is no sensor in the

coffee maker. Please contact your supplier for help.

The message b. TEMPERATURE TOO HIGH indicates that the temperature is too high during the operation of the coffee

maker. Cool the coffee maker and restart the appliance. If the message is still on the display after starting the appli-

ance, the sensor is damaged.

The message c. BREW UNIT BLOCKED indicates that the brewing head unit (14) is blocked and coffee cannot be

brewed. Open the service door (15), take out the brewing head unit (14) and check if it is in the “start position”. Next

reinstall the brewing head unit (14) and close the door (15). The whole procedure is described in section 4. Restart the

coffee maker. If the problem still exists even after unblocking the brewing head unit (14), turn to your supplier to solve

the problem.

The message d. RELEASE UNIT indicates that the brewing head unit (14) is slided out. Take out the dregs box (22),

close the service door (15) and restart the coffee machine. Press and hold for 5 seconds the (B)

button, the brew-

ing head unit (14) will slide out due to the reverse movement of the electric motor. Install the dregs box (22) properly

and brewing head unit (14) and close the door (15). Restart the coffee maker.

The message e. TOP SWITCH FAILURE indicates that the top switch above the brewing head unit (14) does not function

properly. Open the service door (15) to check if the brewing head unit (14) is blocked. After cleaning the unit (see sec-

tion 4) install the brewing head unit (14) and close the door (15). Restart the coffee maker. If you still hear the noise,

it means that the top switch is damaged and repair is necessary.

The message f. SET ROTARY KNOB indicates that the steam/hot water knob (13) is in the position during coffee

brewing. Set the knob (13) in the 0 position during coffee brewing.

The message g. DREGS BOX MISSING indicates that the dregs box (22) might not be properly installed during the cof-

fee brewing process. Check and install the dregs box (22) properly according to section 10.

The message h. FILL TANK WITH FRESH WATER indicates that there is not water in the tank (3). Immediately ﬁ ll the

water tank (3) with fresh water according to section 6.

The message i. FILL TANK WITH SOLUTION indicates that there is no descaling solution in the tank (3). If this mes-

sage is displayed at the beginning of the descaling process, immediately ﬁ ll the water tank (3) with the solution accord-

ing to section 16.7.

The message j. EMPTY DREGS BOX indicates that the coffee maker brewed 8 (9) cups of coffee. Empty and clean the

dregs box (22) according to section 10. It is also advantageous to clean the brewing head unit (14) according to sec-

tion 18.7.

The message k. DATA LOSS indicates the lack of initial settings in the EEPROM memory or the loss of this data. Further

operation of the coffee maker is only possible with default settings. This message disappears after 5 seconds.

The message l. WATER FLOW ERROR indicates that the brewing heat unit (14) ﬁ lter is blocked or the water pipe is

blocked. Take out the brewing head unit (14) and check if the ﬁ lter is blocked. If there are a lot of coffee remains, clean

the brewing head unit (14) (see section 18.7) and insert it back into place (see section 4). If there is no problem with

the brewing head unit (14) try to brew several cups of coffee or to prepare a cup of hot water. If you cannot remove the

brewing head unit (14) proceed according to section 19.7. If the problem still exists, the ﬂ owmeter might be damaged.

The message m. DOOR OPEN indicates that the service door is open (15). Close the door.

The message n. NO ELECTROMAGNET SWITCH indicates that the sensor does not recognize the electromagnetic

switch. This message should disappear after 5 seconds. If the message appears several times it means that the elec-

tromagnetic switch might be damaged. The coffee maker must be repaired.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zelmer 13Z011 Seite 225

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info