781890
20
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
20 І 24
Troubleshooting
Supposed malfunctions, errors or damages are often caused by events which can be remedied by the operator. Therefore
check the power tool on the basis of the following table before you contact a specialist. Many malfunctions may thus be rem-
edied.
Problem Possible cause Approach
1. Power tool does not
start
Power supply interrupted Check power supply by connecting another power tool
Power cord or plug defective Have an electrician check the tool
Other electrical defect of the power tool Have an electrician check the tool
2. Power tool does
not operate with full
power
Extension cord too long and/or cross-
section too small
Use extension cord with permissible length and/or
adequate cross-section
Power supply (e.g. generator) voltage
too low
Connect power tool to an appropriate power supply
3. Poor operation
results
Power tool worn out Replace insertion tool
Grinding plate worn out Have grinding plate replaced
4. Considerable dust
formation
Brush edge worn out Have brush edge replaced
Dust extraction not connectred /
switched on
Connect / switch dust extraction
After use
1. Switch off the power tool as described, disconnect it
from the power supply and Iet it cool down.
2. Clean and maintain the power tool as described below,
and store it carefully.
Cleaning, maintenance and repair
WARNING! Unplug the power tool before starting to
work on it (e.g. transport, installation, retrotting,
cleaning and maintenance)!
Cleaning
a) Keep protective devices, ventilation openings and mo-
tor housings free from dust and dirt as far as possible.
b) Wipe the power tool with a clean cloth or remove dust
and dirt with compressed air at low pressure (max. 3
bar).
c) Clean the power tool immediately after each use.
d) Do not use any detergents or solvents as they may
affect the plastic parts of the power tool. Make sure to
avoid any water ingress into the tool.
Replacing the power supply line
lf the power supply line of this power tool is damaged, it
must be replaced by the manufacturer or the customer
service or any equally qualied person in order to avoid
risks.
Maintenance
Check the power tool and accessory parts (e.g. insertion
tools) for wear and darnage before and after each op-
eration. lf necessary, replace worn out or damaged parts
with new parts and make sure to comply with the oper-
ating instructions. Observe any technical requirements.
Grinding plate, brush edge
Have a qualied specialist replace damaged or worn out
grinding plates (9) and brush edges (10) with new ones
of the same type.
Replacing the power supply line
lf the power supply line ofthispower tool is damaged, it
must be replaced by the manufacturer or the customer
service or an equally qualied person in order to avoid
risks.
WARNING! There are no parts inside the power tool
which can be serviced by the operator! Never open
the power tool! Take it to a qualied specialist for
further maintenance!
Storage and transport
1. Whenever you do not use the power tool, you must
keep it in a dry and weil ventilated place out of the
reach of children, e.g. on a high cabinet or in a closed
place.
2. Keep power tool, instruction manual and accessory
parts, if any, together in the original packaging, if pos-
sible. Thus you have all information and parts avail-
able at any time.
3. Always hold the power tool by its handle.
4. To avoid transport damages, you must pack the power
tool or use the original packaging.
5. Protect the power tool against vibrations and shock,
especially during transport in vehicles.
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Zgonc YPL 710 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info