Bedienungsanleitung Zibro Laser FF 95 (Seite 43 von 71) (Englisch, Holländisch, Französisch)

481445

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

☞

Chapter 2, OPERATION

Step 3: The correct use of ‘SAVE’

The ‘SAVE’ function allows you to limit the temperature.

When this function is activated, the heater will automati-

cally switch off, when the room temperature exceeds the

set temperature by 2°C. Subsequently, when the room

temperature has dropped again to the set temperature,

the heater will automatically switch on again. Activate

the ‘SAVE’ setting by pressing the appropriate button.

The SAVE indicator light will light up. Switch off the

function by pressing the SAVE button once again.

Without the ‘SAVE’ setting your heater will

maintain the set temperature by approxima-

tion as well, by adjusting its heating capacity.

‘SAVE’ is an economy setting, which you can

use when, for instance, you are not present in

the room or to keep it frost-free.

Step 4: The ‘FUEL’ indicator light

When the FUEL indicator light lights up, it means that

there is only fuel left for 10 more minutes. The count-

down of the remaining heating time can be seen in the

information display. You remove the fuel tank and

refill it outside the living room. If you don’t refill it,

you will hear an alarm signal every two minutes, warn-

ing you to refill the removable tank and after 10 min-

utes the heater will switch off automatically.

6. Timer operation

The timer allows you to switch on the heater automati-

cally at a preset time.

In order to switch on the timer, the correct time must

have been set and the heater should be off. Follow the

procedure below:

[1] Press the TIMER button. The TIMER light and the

information display will start blinking.

[2] Use the adjustment buttons to set the time at which

the heater must ignite. Use the button on the left

(̆hour) to set the hours and the button on the right

(̄min.) to set the minutes (interval of 10 minutes).

[3] Press the ON/OFF button while the information dis-

play is blinking.

[4] After approximately 10 seconds the information dis-

play will show CLOCK again and the TIMER indicator

light will light up, indicating that the timer function

has been activated.

To clear the timer setting, press the ON/OFF button once.

Note: When the room temperature is less than

15°C, the preset time is changed automatically

depending on the room temperature in order

to heat the room by the desired time.

Room temperature

Ignition time

More than 15°C Set time

0°C ~ 15°C 10 minutes before set time

Less than 0°C 20 minutes before set time

7. Room temperature sensor

The room temperature sensor is fitted with a 2.5 meter

cable. This is located on the back of the heater. Ensure

that the cable does not touch the outlet tube. The

room temperature sensor can be installed with cello

tape or with a wood screw.

Select the location where the sensor is to be installed in

such a way that it will not be exposed to direct sun-

light, draughts or the warm air flowing out of the

heater.

8. Childproof lock

The childproof lock can be used to prevent children

accidentally changing the heater settings. When the

heater is burning and the childproof lock is on, the

heater can only be switched off. Other functions are

blocked then. If the heater has already been switched

off, the childproof lock also prevents accidental ignition

of the heater. Activate the childproof lock by pressing

the appropriate button and holding it down for more

than 3 seconds. The KEY-LOCK indicator light will light

up, indicating that the childproof lock has been activat-

ed. Switch off the childproof lock by pressing the but-

ton and holding it down for more than 3 seconds once

again.

9. Switching off the heater

There are two ways to switch off the heater.

[1] Press the ON/OFF button. The information display

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zibro Laser FF 95 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zibro Laser FF 95

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info