Bedienungsanleitung Zibro Laser FF 95 (Seite 44 von 71) (Englisch, Holländisch, Französisch)

481445

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

☞ ☞

Chapter 2, OPERATION

will show the CLOCK signal. The air circulation ven-

tilator and the ventilator motor continue to operate

for approximately 3 minutes in order to cool the

heater down.

[2] Press the TIMER button, when you want to switch

off the heater and ignite it again with the timer the

next time. This not only switches off the heater, but

it also activates the timer function. You can change

the required time with the adjustment buttons.

10. Recovery after overheating

The heater is protected against damage caused by

overheating.

A sensor will activate if the temperature in the housing

exceeds 90°C.

Step 1: Switch the heater OFF.

Step 2: Allow the heater to cool down.

Ensure that the metal housing has cooled

sufficiently before touching it.

Under normal conditions, a period of 30 to 45 minutes

is sufficient to allow the heater to cool down

completely.

Step 3: Pull the heater plug out of the socket.

Step 4: Look for the source of the overheating.

Overheating is usually caused by objects that obstruct the

free flow of air. Check that the circulation ventilator or

exhaust pipes are not blocked. Check that there are no

objects blocking the outlet system.

Step 5: Remove the front panel.

Step 6: Clean the inside of the heater.

Before starting to clean the heater, ensure that

the interior is cool enough to touch. Wipe all

dust off the outside of the housing with a clean,

non-fluffy, damp cloth or another suitable

cleaning aid. Do not forget to clean the outside

of the heat chamber and the heat exchanger.

Step 7: Re-attach the front panel.

Step 8: Insert the heater plug into the socket.

Step 9: Switch the heater ON.

Step 10: Re-program the heater (clock and timer).

If the heater overheats after the completion of a

recovery procedure, contact your dealer and do

not switch the heater on until the problem has

been resolved.

11. Cleaning the filter (monthly)

Switch off the heater and let it cool down, before you start

any maintenance work. Also disconnect the plug from the

mains.

Your Zibro needs hardly any maintenance. It is, however,

important that you clean the louvers, grilles and circulation

fan cover on the back of the heater weekly. Periodically

check the flue pipe connection for leakage or separation.

Regularly inspect the fuel filter as well:

[1] Remove the removable tank from the heater and

remove the fuel filter. Some drops may leak from the

filter; keep a cloth at hand.

[2] Remove the dirt by tapping the fuel filter upside-down

against a hard surface. (Never clean it with water!)

[3] Reinstall the fuel filter into the heater.

We recommend that you remove dust and stains in time

with a damp cloth, because otherwise these may cause

stains that are hard to remove.

Do not remove any heater components yourself.

Always contact your Zibro dealer for repairs.

When the power cord is damaged, it may only

be replaced by an authorized fitter. Use a new

cord of the type H05 VV-F.

12. Before consulting an expert

The following situations do not indicate defects.

While switching the heater on or off.

White smoke can be seen when the heater is switched on

for the first time.

Machine oil or dust on the burner chamber or heat

exchanger is burning.

The flames flicker for several minutes after the heater has

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zibro Laser FF 95 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zibro Laser FF 95

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info