Bedienungsanleitung ZyXEL VMG8825-Bx0B (Seite 126 von 434) (Englisch)

796882

126

Zoom out

Zoom in

Vorherige Seite

1/434

Nächste Seite

Chapter 6 Broadband

VMG/XMG Series User’s Guide

126

The following table describes the labels in this screen.

Table 31 Network Setting > Broadband > Add/Edit New WAN Interface (Routing Mode)

LABEL DESCRIPTION

General Click this switch to enable or disable the interface. When the switch goes to the right , the

function is enabled. Otherwise, it’s not.

Name Specify a descriptive name for this connection.

Type Select whether it is an ADSL/VDSL over PTM or ADSL over ATM connection.

Mode Select Routing if your ISP give you one IP address only and you want multiple computers to share

an Internet account.

Encapsulation Select the method of encapsulation used by your ISP from the drop-down list box. This option is

available only when you select Routing in the Mode field.

The choices depend on the connection type you selected. If your connection type is ADSL/VDSL

over PTM, the choices are PPPoE and IPoE. If your connection type is ADSL over ATM, the choices

are PPPoE, PPPoA, IPoE and IPoA. If your connection type is Ethernet, the choices are PPPoE and

IPoE.

IPv4/IPv6 Mode Select IPv4 Only if you want the Zyxel Device to run IPv4 only.

Select IPv4 IPv6 DualStack to allow the Zyxel Device to run IPv4 and IPv6 at the same time.

Select IPv6 Only if you want the Zyxel Device to run IPv6 only.

PPP Information (This is available only when you select PPPoE or PPPoA in the Mode field.)

PPP User Name Enter the user name exactly as your ISP assigned. If assigned a name in the form user@domain

where domain identifies a service name, then enter both components exactly as given.

PPP Password Enter the password associated with the user name above. Select password unmask to show your

entered password in plain text.

PPP Connection

Trigger

Select when to have the Zyxel Device establish the PPP connection.

Auto Connect - select this to not let the connection time out.

On Demand - select this to automatically bring up the connection when the Zyxel Device

receives packets destined for the Internet.

Idle Timeout This value specifies the time in minutes that elapses before the router automatically disconnects

from the PPPoE server.

This field is not available if you select Auto Connect in the PPP Connection Trigger field.

PPPoE

Passthrough

This field is available when you select PPPoE encapsulation.

In addition to the Zyxel Device’s built-in PPPoE client, you can enable PPPoE pass through to

allow up to ten hosts on the LAN to use PPPoE client software on their computers to connect to

the ISP via the Zyxel Device. Each host can have a separate account and a public WAN IP

address.

PPPoE pass through is an alternative to NAT for application where NAT is not appropriate.

Disable PPPoE pass through if you do not need to allow hosts on the LAN to use PPPoE client

software on their computers to connect to the ISP.

ATM PVC Configuration (These fields appear when the Type is set to ADSL over ATM.)

VPI [0-255] The valid range for the VPI is 0 to 255. Type the VPI assigned to you.

VCI [32-65535] The valid range for the VCI is 32 to 65535 (0 to 31 is reserved for local management of ATM

traffic). Enter the VCI assigned to you.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

ZyXEL VMG8825-Bx0B Seite 126

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info