Bedienungsanleitung Alecto DBX-63 (Seite 51 von 56) (Deutsch, Englisch, Holländisch, Französisch)

707244

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

5.5 TEMPERATURE ALARM:

The display of the parent unit shows the temperature transmitted by the

baby unit. You can assign a minimum or maximum temperature to this

function and have the unit sound an alarm when these values are exceeded:

1. briey press the button to activate the touch-

screen

2. press and hold the M button for 3 seconds to

open the menu

3. use the and buttons to select the option

TEMP ALARM

4. briey press the M button

5. use the and buttons to select whether you

want to set or adjust the lower or the upper limit

6. briey press the M button

7. use the and buttons to adjust the selected temperature limit and

briey press the M button

8. repeat step 5-7 if you want to set the other temperature limit

9. briey press the button to conrm the set temperature limits and to

leave the menu

• the upper limit can be set between -3°C and 50°C

• the lower limit can be set between -19°C and 3 degrees lower than the

upper limit

• select ‘‘OFF” if you don’t want to set an upper or lower limit

• when the set temperature limit is exceeded, the temperature display will

start flashing while ‘TOO WARM’ or ‘TOO COLD’ is shown

• if the ALARM TONE function is activated, you’ll also hear short

notification tones

• don’t forget that the temperature display is only an indication, you’ll have

to take a tolerance of +/- 2°C into account

• at temperatures above 50°C and under -19°C, ‘- -’ will appear in the

display

5.3 DISPLAY LIGHT BRIGHTNESS:

You can adjust the intensity of the display light as follows:

1. briey press the button to activate the touch-screen

2. press and hold the M button for 3 seconds to open

the menu

3. use the and buttons to select the option

BRIGHTNESS

4. briey press the M button

5. use the and buttons to select the desired

brightness

6. briey press the button to conrm you selection

and to leave the menu

• you can choose from 8 brightness levels

• a high brightness level ensures good readability, but also uses more

power.

5.4 NAME OF THE BABY UNIT:

Instead of the standard name “BABY-1” of the baby unit, you can program

your own chosen name.

1. briey press the button to activate the touch-screen

2. press and hold the M button for 3 seconds to

open the menu

3. use the and buttons to select the option

NAME

4. briey press the M button

5. use the and buttons to select the desired

baby unit (only when using multiple baby units)

6. briey press the M button, ‘BABY 1’ will appear

in the display (or another name you already set

earlier) and the cursor ( _ ) will ash underneath the rst letter

7. change the rst letter using the and buttons and briey press the M

button

8. repeat step 7 until the name is fully entered

9. briey press the button to conrm you selection and to leave the

• you can choose any of the 26 letters in the alphabet, the numbers 0-9

and a space

• the name has a maximum length of 14 characters, including spaces

• you cannot correct a mistake; in this case, leave the setting and start

again

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alecto DBX-63 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info