Bedienungsanleitung Alecto DVM-135 (Seite 5 von 8) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

803219

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Read and keep the instructions. All the safety and

operating instructions should be read before use.

To use your parent unit and baby unit together, you must

be able to establish a radio link between them.

The range will be affected by environmental conditions.

Any large metal objects, reinforced concrete, other solid

structures, radio or electrical equipment between the

baby and parent unit may block the radio signal.

The use of other 2.4GHz products may cause

interference with this product, so keep the baby unit away

at least 1.5 meter from these type of products or turn the

products off if they appear to be caused interference.

This device can’t replace responsible adult supervision.

This device is designed for indoor use only.

The units should not be exposed to rain or moisture.

The units should not be exposed to direct heat sources.

This product is not a toy and should be kept out of

children’s reach.

This product contains small parts, take care when unpac-

king and assembling the product.

Children can become entangled in the cords, therefore

power cords should be kept more than 1 meter away

from the crib and baby’s reach at all times.

The baby units with power cords should never be hung

on or near the crib.

The units should only be used with the AC power

adapters included in this package (rated 5V; 1.0A).

Improper or incorrect use of batteries may cause

corrosion or battery leakage, which could cause personal

injury or damage to property. Use only the types of the

batteries which are indicated in this manual.

Don’t use the units if the cord or plug is damaged.

Don’t attempt to repair or adjust any of the electrical or

mechanical functions of the unit, if you do, the guarantee

will be made void.

This product should not be used on or under surfaces

that may block the ventilation openings.

This product must not be placed in an enclosed area that

may impede the air ow.

2. MODE OPERATION

2.1 Power save/screen off

Short press power key to turn on/off the screen of the

parent unit.

2.2 Volume adjustment

Press the UP key to increase the volume. Press the

DOWN key to decrease the volume.

2.3 Brightness adjustment

Press the RIGHT key to increase the brightness.

Press the LEFT key to decrease the brightness.

2.4 Baby unit view/scan (in case of 2 baby units)

Press the scan key / to view/scan the baby units.

During the scan mode, the scan icon will be displayed

on top of the screen. Each baby unit video will stay on the

screen for about 10 seconds, after the 10 seconds another

baby unit video will display on the parent unit etc.

2.5 Digital zoom & move the screen.

Press and hold the key zoom / for about 2 seconds to

operate the zoom in/out function.

After you’ve zoomed in, press the LEFT key to pan left,

press the RIGHT key to pan right, press the UP key to

tilt up and press the DOWN key to tilt down. During the

digital zoom mode, the icon 2 will be displayed on top of

the screen.

Note 1: The baby unit doesn’t move by operating the pan/

tilt function.

Note 2: If you want to adjust the volume/brightness, you

have to exit the zoom mode before you can operate it.

2.6 Talk to the baby

To talk, press and hold the talk / key. The microphone

icon will be displayed in the lower right corner of the screen

while this function is activated.

Release the button when you don’t want to talk anymore. Now

you can listen to the baby’s room.

Note: Bear in mind that you can’t listen to your baby whilst

you’re talking. If you want to listen to the baby, you have to

stop pressing this button.

2.7 Infrared night vision (automatic)

The infrared night vision function allows the baby unit to pick

up images of your baby or the monitored area in dark or low

light conditions. In this mode, only black and white images will

be displayed on the parent unit. The optimum image is 1.8m / 6

feet distance between the baby unit and object. When the baby

unit is in night vision mode, the icon will be displayed on top

of the screen. This will take a few seconds.

3. MENU OPERATION

3.1 Pairing the baby unit and parent unit

The baby unit is pre-registered to your parent unit. You

don’t need to register it again unless the baby unit loses

its link with the parent unit. To re-register your baby unit, or

Note: Before you begin pairing, be sure to have the

parent unit and baby unit side by side.

1. Press the MENU/OK key. The menu will pop up.

2. Press the LEFT key or RIGHT key until the icon is

highlighted.

3. Press the MENU/OK key.

4. Press the UP key or DOWN key to select ADD CAM

then press the MENU/OK key.

5. While the hourglass icon is displayed, press the PAIR

button on the back of the baby unit.

6. Once paired, it will display on the LCD screen.

7. If unsuccessful, please repeat the above steps.

8. Press the key to exit.

3.2 Delete a baby unit

1. Press the MENU/OK key and the menu will pop up.

2. Press the LEFT key or RIGHT key until the baby unit

icon is highlighted.

3. Press the MENU/OK key to conrm.

4. Press the UP key or DOWN key to select DEL CAM

then press MENU/OK key.

5. Press the LEFT key or RIGHT key to select the

check mark .

6. Press MENU/OK key to conrm the option.

7. Press the BACK key to exit.

3.3 VOX setting / ECO Mode

This mode allows you to control the sound activation of

your baby unit and switch on the ECO mode. If there is no

sound around the baby unit within 30 seconds, the sound

transmission stops and the picture turns black. When the

baby unit detects any sounds louder than the sensitivity

level, the sound and image will turn on again. To change

the VOX level, please follow the below instructions.

1. Press the MENU/OK key and the menu will pop up.

2. Press the LEFT key or RIGHT key until the VOX icon

is highlighted. Press the MENU/OK key. Then press the

UP key or DOWN key to select the desired level.

3. Press the MENU/OK key to conrm.

4. Press the BACK key to exit.

Note 1: Once the VOX is turned on, the VOX icon ,

or will display on top of the screen.

Note 2: is Low sensitivity. The baby have to make a

lot of sound before the VOX function will be activated.

is High sensitivity level. The baby don’t have to make

a lot of sound before the VOX function will be activated.

Note 3: ECO mode does not work with 2 or more baby

units.

DECLARATION OF CONFORMITY

Hereby, Commaxx declares that the radio equipment type Alecto

DVM135 is in compliance with directive 2014/53/EU. The full text of the EU decla-

ration of conformity is available at the following internet address: http://DOC.hesdo.

com/DVM135-DOC.pdf

3.4 Temperature unit setting

1. Press the MENU/OK key. The menu will pop up.

2. Press the LEFT key or RIGHT key until the

temperature icon is highlighted. Press the MENU/OK key.

3. Navigate with the arrows to select or .

4. Press the MENU/OK key to conrm.

5. Press the BACK key to exit.

Note: For this unit, the environment test temperature range

is 0-40 .

Environment temperature alarm setting

1. In the menu, go to the icon. Press the MENU/OK button.

2. Use the arrows to turn the alarm on or off . Press

the MENU/OK button to conrm.

3. Navigate with the arrows to move to the alarm tempera-

ture values. Icon is the lowest temperature value. Icon

is the maximum temperature value.

Press the UP key or DOWN key to adjust the maxi-

mum environment temperature alarm value. After it is set,

press the MENU/OK key to conrm.

When the highest temperature alarm value is set, it will

automatically jump to the lowest temperature alarm value

set. Now, the low temperature alarm value appears in a red

box, press the UP key or DOWN key to make lowest

environment temperature alarm value adjustment, then

press the MENU/OK key to conrm. The system returns to

the beginning automatically. If you don’t want to change the

temperature value, press the BACK key to exit.

Note: The high temperature alarm range is from

4-40 . The low temperature is from 0-36 .

The temperatures cannot be closer than 4 difference.

3.5 Lullaby setting

You can soothe the baby to sleep by playing a gentle

lullaby from the baby unit.

1. Press the MENU/OK key and the menu will pop up.

2. Press the LEFT key or RIGHT key until the lullaby

icon is highlighted. Press the MENU/OK key.

3. Navigate with the arrows to select 1 of the 8 lullabies.

4. Press the MENU/OK key to conrm.

5. Press the BACK key to exit.

Note 1: Once the lullaby is turned on, the lullaby icon

will display on top of the screen.

Note 2: The lullaby default setting is OFF.

Note 3: Lullaby loop playing function will play all the

lullabies one by one.

3.6 Alarm setting

You can use the alarm to remind yourself to feed your baby

/ change diaper / sleep, etc.

1. Press the MENU/OK key and the menu will pop up.

2. Press the LEFT key or RIGHT key until the alarm

icon is highlighted. Press the MENU/OK key.

3. Navigate with the arrows to select the desired time

interval.

4. Press the MENU/OK key to conrm.

5. Press the BACK key to exit.

Note 1: The minimum alarm setting is 0.5 hour. The

maximum alarm setting is 5 hours. In total there are 8

levels.

Note 2: Once the alarm is turned on, the alarm icon

will display in the lower left corner of the screen.

Note 3: The alarm default setting is OFF.

Note 4: When the alarm is ringing, press any key on the

parent unit to turn the alarm off.

Note 5: If you don’t turn off the alarm, the alarm will ring

for 1 minute. After three minutes the alarm will ring again

for 1 minute. The alarm will ring for three times in total,

after this the alarm goes off.

4. TROUBLE SHOOTING

No reception

on the parent unit The power adapters may not be properly connected.

Conrm that the baby unit and parent unit are ON.

The baby unit may be too far away from the parent

unit.

The baby unit and parent unit may not be properly

paired. Follow §3.1.

Interference or poor

reception Move the parent unit closer to the baby unit.

The baby unit or parent unit may be placed too

close to metal objects.

Other electronic devices may be interfering with the

signal. Turn off those devices.

The battery power may be too low.

Howling (static,

screeching) The baby unit and parent unit may be placed too

close together.

The volume on the parent unit may be set too high.

Can’t hear the baby

on the parent unit Volume setting may be too low.

Image frozen Restart the baby unit (plug out the adapter, then

plug it into the socket again).

Press the reset key at the back of the parent unit.

5. SPECIFICATIONS

Frequency 2.4GHz FHSS

Frequency range 2412 - 2469 MHz

Maximum power <19 dBm

Operating Range Indoor: Up to 50 meters

Outdoor: Up to 300 meters

(straight line and open space)

LCD 3.5” TFT LCD

Operating time with

battery fully charged

Up to 10 hours (VOX on)

Display

resolution

352x264 RGB

Rechargeable batte-

ry for parent unit

Li-polymer battery pack

3.7V; 2000mAh; 4.70Wh

Operating environ-

ment

Temperature: 0°C to 40°C (32°F to 104°F)

Relative humidity: 15% - 85%

Storage

environment

Temperature: -20°C to 70°C (-4°F to 158°F)

Relative humidity: 15% - 85%

Power adapter Model: K05S050100G

Power adapter input Input: 100-240VAC~50/60Hz 0.2A

Output: 5.0V DC, 1.0A

Output power 5.0 W

Average active

efficiency

73.7%

Efficiency at low

10% load

No load Power

consumption

0.1 W MAX

1. WARNINGS & SAFETY INSTRUCTIONS

v1.1

www.alectobaby.nl

DVM135BK

DVM135

Commaxx BV

Wiebachstraat 37

6466 NG, Kerkrade

The Netherlands

Alecto DVM-135 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info