Bedienungsanleitung Allen-Heath MixWizard WZ4-16 (Seite 16 von 32) (Englisch)

541379

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Allen & Heath 16 WZ

16:2 and 12:2 User Guide

AUX SENDS These rotary controls adjust how much channel signal is

mixed to the aux outputs. Each of the 6 auxes has its own control. They

adjust from fully off to +6dB boost. Unity gain 0dB is marked at 3 o’clock

position. Factory default settings should satisfy the most common applica-

tions:

AUX1, AUX2 = Pre-fade

AUX3, AUX4 = Switched pre/post using PRE switch

AUX5, AUX6 = Post-fade

Pre-fade aux options: Pre-INSERT, pre-EQ, post-MUTE

These settings may be changed if preferred by repositioning internal jumper

link / solder link options. They offer many different combinations of pre and

post-fade sends, and a post-EQ option for the pre-fade sends. The PRE

switch can be assigned to one, two or more of the sends. More detail is

provided in OPTIONS later in this guide.

Pre-fade aux sends are not affected by the channel fader movements. These

are typically used to feed stage monitors. In most cases users also prefer

that the monitor sends are not affected by inserted processors or the chan-

nel EQ. Post-fade aux sends follow the channel faders and are typically used

to send a proportion of the channel signal to an effects device such as reverb

or delay. Pre or post-fade sends may also be used for special applications

such as recording, zone feeds, clean feeds and aux fed subs.

PRE When pressed the pre-fade channel signal is sent to the associated

auxes. When released the post-fade signal is sent. Auxes 3 and 4 are affect-

ed by the PRE switch (factory default). You can change this to dedicated pre

-fade using the internal options.

PAN Positions the channel signal between L and R in the stereo mix. The

centre position (mono image) is detented for quick resetting.

MUTE When pressed the channel signal is turned off. This affects the feed

to the LR mix, pre and post-fade aux sends and direct output, but does not

affect the insert send. The red indicator lights when the channel is muted.

PFL Press PFL to listen to the pre-fade channel signal in the headphones or

AB monitor (if configured) without affecting the main outputs. The console

main LR meters are interrupted with the channel signal. The red PK indica-

tor half lights to show that PFL has been selected on that channel. Selecting

more than one PFL at the same time mixes those signals together in the

monitor.

PEAK The red indicator illuminates when the channel pre-fade signal is

within 5dB of clipping. This gives you enough warning to reduce the GAIN

control before you hear signal distortion.

SIGNAL The green signal presence indicator lights when the channel pre-

fade signal is greater than -12dBu.

FADER Controls the channel level feeding the main LR mix and post-fade

aux sends. It also affects the direct output if this has been set to post-fade

using the internal option jumper. The fader provides +10dB maximum boost

above its normal unity gain 0dB position.

Important note on setting channel levels: Use PFL to set the GAIN

controls for correct signal level through each channel. Use the faders to

balance each signal in the mix. These are typically operated around their -20

to 0 positions according to the mix. We do not recommend setting the

faders to ‘0’ and mixing using the GAIN controls.

180

35Hz

400

250

(LINE)

700

500Hz

15k

HPF

+48V

PAD

SIG

AUX

PRE

PFL

MUTE

AUX

PAN

PK!

POST

10- 10

GAIN

4060

EQ IN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Allen-Heath MixWizard WZ4-16 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info