Bedienungsanleitung Alpine RUX-C800 (Seite 40 von 67) (Englisch)

471407

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

38-EN

01GB07PXAH800.fm

ALPINE PXA-H800_EN 68-13530Z65-A (B5)

From the Commander

When you modify the “FRONT HIGH” speaker setting to [Full], a

message to confirm the change will be displayed. To set up at “Full

Range,” rotate the [Rotary encoder] to select “OK”, and then press

the [Rotary encoder]. Make sure the speaker being used for this

output is able to handle a full range source. Many tweeters can be

damaged when driven by a full range signal.

This item is enabled for setup only when 2 subwoofers are connected.

Rotate the [Rotary encoder] to select “Stereo” or “Mono”, and then

press the [Rotary encoder].

Stereo: Subwoofer stereo (L/R) output

Mono: Subwoofer monaural output

• Speakers that cannot be turned off are disabled for setup. Refer to

Table 1 (Output System) in “System Configuration” (page 60).

• When you connect just one subwoofer, turn off “Subwoofer2.”

7-1

First time start-up:

The AUX Input System Select screen will be

automatically displayed. Continue to set, referring to

“Setting the AUX Input System (AUX Input Setup)”

(page 39).

7-2

Subsequent start-up:

The “Turn ACC Off” screen will be displayed. Turn the

ignition key to off and then on again. The settings

become effective.

• If [ ] is pressed during setting, the unit returns to the previous

item.

• If the speaker system is changed, all setup values except those for

AUX input will be restored to the initial setup values.

• You can also set the speakers from “Setting the Speakers (Speaker

Setup)” (page 38).

• You can also set the subwoofer output from “Setting the Subwoofer

Output (SW Channel)” (page 38).

• After the setting, it is recommended to store the setting contents on

the unit. For details, refer to “Storing the Preset Values (Preset

Store)” (page 36).

Setting the Speakers (Speaker Setup)

Turn on the connected speakers.

Press [FUNC.].

Rotate the [Rotary encoder] to select “Output

Setup,” and then press the [Rotary encoder].

Rotate the [Rotary encoder] to select “Speaker

Setup,” and then press the [Rotary encoder].

The Speaker selection screen is displayed.

Rotate the [Rotary encoder] to select the speaker to

be set, and then press the [Rotary encoder].

Setting contents: Front High/Front Mid/Front Low/Rear/

Center/Subwoofer (1, 2)

• Speakers to be set vary depending on the system set in “Setting the

Speaker System (System Select)” (page 37).

• Speakers that cannot be turned off are disabled for setup. Refer to

Table 1 (Output System) in “System Configuration” (page 60).

Rotate the [Rotary encoder] to select “ON” or “OFF,”

etc., and then press the [Rotary encoder].

Repeat the steps until all the speakers are set.

Front High*: OFF/Tweeter/Full

Front Low: OFF/ON

Rear: OFF/ON

Center: OFF/ON

Subwoofer(1, 2): OFF/ON

* When you modify the “Front High” speaker setting to [Full], a

message to confirm the change will be displayed. To set up at “Full

Range,” rotate the [Rotary encoder] to select “OK”, and then press

the [Rotary encoder]. Make sure the speaker being used for this

output is able to handle a full range source. Many tweeters can be

damaged when driven by a full range signal.

• When you connect just one subwoofer, turn off “Subwoofer2.”

To set up other speakers, press [ ] and repeat

Steps 4 and 5.

When the setting is complete, press and hold [ ]

for at least 2 seconds.

• If [ ] is pressed during setting, the unit returns to the previous

item.

• When the speaker setting is changed while ImprintEQ/RoadEQ is on,

ImprintEQ/RoadEQ will be turned off after a confirmation message

is displayed.

• After the setting, it is recommended to store the setting contents on

the unit. For details, refer to “Storing the Preset Values (Preset

Store)” (page 36).

Setting the Subwoofer Output (SW

Channel)

You can set the subwoofer output to stereo or monaural. Make sure to

set the correct output for your subwoofer type. (Initial Setting: “Mono”)

Press [FUNC.].

Rotate the [Rotary encoder] to select “Output

Setup,” and then press the [Rotary encoder].

Rotate the [Rotary encoder] to select “SW Channel,”

and then press the [Rotary encoder].

The Subwoofer Channel selection screen is displayed.

Rotate the [Rotary encoder] to select “Mono” or

“Stereo,” and then press the [Rotary encoder].

Mono: Subwoofer monaural output

Stereo: Subwoofer stereo (L/R) output

01GB00PXAH800.book Page 38 Tuesday, February 8, 2011 9:04 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine RUX-C800 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info