Bedienungsanleitung Alpine RUX-C800 (Seite 57 von 67) (Englisch)

471407

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

55-EN

01GB07PXAH800.fm

ALPINE PXA-H800_EN 68-13530Z65-A (B5)

From the Commander

Adjusting the Acoustic Image (BI-

PHANTOM)

To install a center speaker, it must be located in the dash, an equal

distance between the Left and Right speakers. In most cases, this is very

difficult to achieve. Using Bi-PHANTOM, a virtual center speaker is

created by sending the center channel information to both the Left and

Right speakers. Adjusting the center width in Dolby Pro Logic II

“Music” (see “Using Dolby Pro Logic II (Dolby PLII)” on page 53),

makes this function ineffective. This is used in a system where there is

no sub-woofer and the rear speakers can produce lower frequency

sounds than the front speakers. (Initial setting: “OFF”, “±0 dB”)

Press [FUNC.].

Rotate the [Rotary encoder] to select “Multi Ch.

Setup,” and then press the [Rotary encoder].

Rotate the [Rotary encoder] to select “BI-

PHANTOM,” and then press the [Rotary encoder].

Rotate the [Rotary encoder] to select “ON,” and then

press the [Rotary encoder].

Turning this feature on creates the acoustic image in which

the center speaker is virtually located exactly in front of the

listener by splitting the sound of the center speaker into

both sides.

Adjust the level by rotating the [Rotary encoder].

LEVEL: -5 to +5 dB (in 1 dB steps)

The level can be adjusted between -5 and +5. When the

level becomes greater, the acoustic image moves from the

center speaker location toward both sides.

When the setting is complete, press and hold [ ]

for at least 2 seconds.

• If [ ] is pressed during setting, the unit returns to the previous

item.

• Do not perform operations such as Stop/Pause/Disc Exchange/Cue/

Fast Forward/Audio Switching on the player during this setup

adjustment. When the decode state switches, the settings will be

cancelled.

• When the Center speaker is off in “Setting the Speaker System

(System Select)” (page 37)/“Setting the Speakers (Speaker Setup)”

(page 38), this item cannot be set.

• Effective only for Dolby Pro Logic II, EUPHONY and DTS (with

Center signal).

• After the setting, it is recommended to store the setting contents on

the unit. For details, refer to “Storing the Preset Values (Preset

Store)” (page 36).

Mixing the Low Range Audio for the Rear

(Rear Mix)

This function mixes the front channel audio signals to the audio signals

output from the rear speakers, improving the sound in the vehicle’s rear

seat. This is used in a system where there is no subwoofer and the rear

speakers can produce lower frequency sounds than the front speakers.

(Initial setting: “OFF”, “±0 dB”)

Press [FUNC.].

Rotate the [Rotary encoder] to select “Multi Ch.

Setup,” and then press the [Rotary encoder].

Rotate the [Rotary encoder] to select “Rear Mix,” and

then press the [Rotary encoder].

Rotate the [Rotary encoder] to select “ON,” and then

press the [Rotary encoder].

Turning this feature ON mixes the audio signals output from

the rear speakers with the front audio signals.

Adjust the level by rotating the [Rotary encoder].

LEVEL: -6/-3/0/+3/+6 dB

The level can be adjusted in 5 steps. The higher the level,

the more the low range audio is output from the rear

speakers. (Depending on the software such as DVD, the

effect may vary.)

When the setting is complete, press and hold [ ]

for at least 2 seconds.

• If [ ] is pressed during setting, the unit returns to the previous

item.

• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding

or switching the audio channel of this unit while making this

adjustment. The setting is cancelled if the decode mode is switched.

• When the Rear speaker is off in “Setting the Speaker System (System

Select)” (page 37)/“Setting the Speakers (Speaker Setup)”

(page 38), this item cannot be set.

• Effective only for Dolby Pro Logic II, EUPHONY and DTS (with

Rear signal).

• After the setting, it is recommended to store the setting contents on

the unit. For details, refer to “Storing the Preset Values (Preset

Store)” (page 36).

01GB00PXAH800.book Page 55 Tuesday, February 8, 2011 9:04 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alpine RUX-C800 Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info