Bedienungsanleitung American Audio Q-2422 PRO (Seite 10 von 22) (Englisch)

603204

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

©American Audio® - www.AmericanAudio.com - Q-2422 PRO User Instructions page 10

Q-2422 PRO FRONT PANEL - CONTROLS AND FUNCTIONS CONT.

mixer. Also be sure you amplifiers are turned off. Remember mixer on first and turned off last.

13. ZONE EQ SECTION -

ZONE TREBLE

CONTROL - This knob is used to adjust the treble levels of the ZONE allowing

for a maximum treble gain of +12dB or maximum decrease of -30dB. Turning the knob in a counter-

clockwise direction will decrease the amount of treble applied to the ZONE signal, turning the knob in

a clockwise direction will increase the amount of treble applied to the ZONE signal.

ZONE BASS CONTROL - This knob is used to adjust the low frequency levels of the ZONE

allowing for a maximum bass gain of +12dB or maximum signal decrease of -30dB. Turning the knob

in a counter-clockwise direction will decrease the amount of bass applied to the ZONE signal, turning

the knob in a clockwise direction will increase the amount of bass applied to the ZONE signal.

ZONE LEVEL VOLUME OUTPUT CONTROL - This rotary knob is used to control the zone level

volume. The zone level is not PFL, it is essentially a second master output volume with separate output

volume control.

14. HEADPHONE JACK -

This jack is used to connect your headphones to the mixer allowing you to

monitor the cue source. Use headphones only rated at 8 ohms to 32 ohms. Most DJ headphones are

rated at 16 ohm, these are highly recommended. Always be sure the CUE LEVEL VOLUME (16) is set

to minimum before you put the headphones on.

15. SPLIT CUE - This button will activate the "Split Cue" function. When used with a set of stereo

headphones, the Split Cue function will assign the Cue signal to the left channel of the headphones

and the Program (main output) signal to the right channel of the headphones. Essentially splitting the

cue signal in half. This process will allow for headphones mixing. The CUE MIXING CONTROL (18) will

also work in conjunction with function. Please note that this function will only work with a set of stereo

headphones.

16. CUE LEVEL VOLUME CONTROL -

This knob is used to adjusts the headphone volume output

level. Turn the knob in a clockwise direction to increase the headphone volume.

. MASTER VOLUME CONTROL - This slider is used to control the master output level (main volume).

To avoid distorted output try to maintain an average output signal level no greater than +4 dB. To

avoid speaker damage that may be caused by excessive volume, be sure this slider is always set to

zero (completely down) before turning the unit on.

18. CUE MIXING CONTROL - This functions allows you to monitor the Cue level as well as the

Program (main output) level in your headphones. A channels Cue Level may only be monitored if the

channels CUE (19) function is selected. To select a channels cue function press the CUE BUTTON

(19) that is directly associated with the specific channel you wish to monitor. You may use the mixing

function to blend both the Cue level and the Program level together. You can vary the output level

to either hear more or less of either of the two levels. Sliding the Cue Mixing fader to the CUE posi

tion (left) will allow you to hear more of the Cue level. Sliding the knob to the PGM position (right) will

allow you to hear more of the Program level (main output). You may also use the Cue Mixing Control

to hear either the Cue level or the Program level exclusively. If the fader is in the full CUE position you

will only hear the cue level, if the fader is in the full PGM position you will only hear the main output.

This function is especially useful when mixing without an monitor.

19. CUE BUTTON - These buttons are used to activate a channels “CUE” mode.

The red CUE LED

will glow when a channels cue mode is activated. The Cue function sends a channels incoming signal

to the headphones. The cue level is adjusted by the CUE LEVEL KNOB (16). Be sure the CUE MIXING

SLIDER (18) is set to the “CUE” position to hear a selected channel source.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

American Audio Q-2422 PRO Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von American Audio Q-2422 PRO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info