Bedienungsanleitung American Audio Q-2422 PRO (Seite 11 von 22) (Englisch)

603204

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

©American Audio® - www.AmericanAudio.com - Q-2422 PRO User Instructions page 11

Q-2422 PRO FRONT PANEL - CONTROLS AND FUNCTIONS CONT.

20. Q-START ON/OFF BUTTON - This function works in conjunction with a compatible American DJ®

or American Audio® “Q” Start CD player. When used with a compatible CD player, you can use the

crossfader to start and stop a CD Player with the slide of the mixer’s CROSSFADER (22). The ON/OFF

“Q" START BUTTTON activates the FADER “Q" START feature. When in the ON position (GREEN LED

WILL BE LIT), the FADER “Q" START automatically returns the CD player to the preset CUE POINT.

For example; Assuming you have two compatible American Audio™ CD players or a

compatible dual CD player connected to channels one and two. When the Fader "Q" Start

option is turned on, sliding the crossfader to the far left position will trigger playback on CD

player 1. When the crossfader is pushed to the far right position, playback on CD player 2 will

begin, and CD player 1 will return to the cue position. Refer to your American Audio CD player

user manual for setting CUE POINTS. Turn the ON/OFF BUTTON to the OFF position (RED

LED IS NOT LIT) to disengaged “Q” Start function and resume to a normal fader.

21. FADER ASSIGN SWITCH - This is a four position switch that assigns a channel to the CROSS-

FADER (22). When a channel is assigned to the left side of the CROSSFADER (22) that channels

output level is routed to and controlled by the CROSSFADER (22). Sliding the CROSSFADER (22) to

left position will send the volume output of the assigned channel to the MASTER VOLUME LEVEL (17),

siding the CROSSFADER (22) to right position will cut that channels volume to MASTER VOLUME

LEVEL (17). The reverse is true for the right channel fader assign switch. When the assign switch is set

to the "OFF" position the crossfader will have no function.

22. FEATHER FADER PLUS CROSSFADER - This fader is used to blend the output signals of chan-

nels one and two together. When the fader is in the full left position (channel 1), the output signal of

channel one will be controlled by the master volume level. The same fundamentals will apply for chan

nel two. Sliding the fader from one position to another will vary the output signals of channels one

and two respectively. When the crossfader is set in the center position, the output signals of both the

channels one and channels two will be even.

23. CHANNEL VOLUME FADER -

These faders are used to control the output signal of any source

assigned to its particular channel. However, master volume is controlled by the MASTER VOLUME

CONTROL (17).

. MIC 2 VOLUME CONTROL - This knob controls the output volume of MICROPHONE 2 (28).

However, master volume is controlled by the MASTER VOLUME CONTROL (17).

. MIC 1 VOLUME CONTROL - This knob controls the output volume of MICROPHONE 1 (2).

However, master volume is controlled by the MASTER VOLUME CONTROL (17).

. TALKOVER CONTROL - This function decreases all signal output except the microphone signal.

The amount of decrease is preset to -14dB and is not user selectable.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

American Audio Q-2422 PRO Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von American Audio Q-2422 PRO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info