792117

Amiko TSC-1000 Seite 10

10
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
User`s Manual
14 / 25
User need to adjust the attitude of the meter according BLUE arraw on the screen. The meter will
deep and the RED icon turns to GREEN if the RED icon closes to the YELLOW one. It is better to make
the two icon overlapping. And also values of azimuth and elevation will refresh on time according to
the current position during the whole process.
Select Compass and press [OK] to go to compass submenu. And the menu as bellowing figure.
5.6
D
I
SE
Q
C
M
ONITOR
Connect other device, such as STB(DVB-S/S2 receiver), by the cable line to the LNB input
port . Then the meter analyzes all input commands for DiSEqC or switch on this menu, and
also shows the power supply and 22K status. The menu displays the last two commands.
Please refer to below screenshot.
Select Compass and press [OK] to go to compass submenu. And the menu as bellowing figure.
User`s Manual
14 / 25
User need to adjust the attitude of the meter according BLUE arraw on the screen. The meter will
deep and the RED icon turns to GREEN if the RED icon closes to the YELLOW one. It is better to make
the two icon overlapping. And also values of azimuth and elevation will refresh on time according to
the current position during the whole process.
Select Compass and press [OK] to go to compass submenu. And the menu as bellowing figure.
5.6
D
I
SE
Q
C
M
ONITOR
Connect other device, such as STB(DVB-S/S2 receiver), by the cable line to the LNB input
port . Then the meter analyzes all input commands for DiSEqC or switch on this menu, and
also shows the power supply and 22K status. The menu displays the last two commands.
Please refer to below screenshot.
5.6 DISEQC MONITOR
Connect other device, such as STB(DVB-S/S2 receiver), by the cable line to the LNB input port . Then the meter
analyzes all input commands for DiSEqC or switch on this menu, and also shows the power supply and 22K
status. The menu displays the last two commands. Please refer to below screenshot.
User`s Manual
15 / 25
Pow: The power supply of the input cable line.
22KHz: The 22k status of the input cable line.
E03F20D1: The command data of the input cable line. The pre-command.
Move centre: The behavior of dish for command E03F20D1.
E13F21D6: The command data of the input cable line. The current command.
Move west one step: The behavior of dish for command E13F21D6.
DiSEqC1.2/USALS: The command protocol type.
Pow: The power supply of the input cable line.
22KHz: The 22k status of the input cable line.
E03F20D1: The command data of the input cable line. The pre-command.
Move centre: The behavior of dish for command E03F20D1.
E13F21D6: The command data of the input cable line. The current command.
Move west one step: The behavior of dish for command E13F21D6.
DiSEqC1.2/USALS: The command protocol type.
6. DVBT/T2/ISDBT
User`s Manual
16 / 25
6.
DVBT/T2/ISDBT
User can measure the live DVB-T/T2 signal, analyze the
spectrum, the scope between transponders , auto scan all
the saved frequencies and list all the locked ones. There
are six submenus: Measure, Auto Scan, RF Channel List ,
Scope, Spectrum chart and ANT power.
6.
1
T
ERRESTRIAL
M
EASURE
The device will show SNR, CBER, VBER, power value,
strength and quality of the connected live signal. Please see
below for detail.
: The lock status. The signal is locking if the icon is green otherwise the
color of the icon is red.
C12: The channel name.
5V, 12V,18V: The antenna output voltage. The color of icon will be green once the voltage
is outputting or the color is gray.
DVB T2: The terrestrial system. The values are DVB T and DVB T2. Press [/]
to switch them.
FREQ: The current frequency. Press [/] to change the frequency or [OK]
to edit it.
BW: The bandwidth of the live signal. Press [/] to switch between 6M,
7M and 8M.
SNR: The signal noise rate value of the live signal.
CBER: The CBER(BER before FEC) value of the live signal.
LBER: The LBER(BER after LDPC) value of the live signal.
LEVEL: The power level value of the live signal.
Str: The strength of the live signal in percent.
Qlt: The quality of the live signal in percent.
10
User need to adjust the attitude of the meter according BLUE arraw on
the screen. The meter will deep and the RED icon turns to GREEN if the
RED icon closes to the YELLOW one. It is better to make the two icon
overlapping. And also values of azimuth and elevation will refresh on
time according to the current position during the whole process.
User can measure the live DVB-T/T2 signal, analyze the spectrum, the
scope between transponders , auto scan all the saved frequencies and
list all the locked ones. There are six submenus: Measure, Auto Scan, RF
Channel List , Scope, Spectrum chart and ANT power.
… 10 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Amiko TSC-1000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info