Bedienungsanleitung Arcam DiVA AVR280 (Seite 9 von 38) (Englisch)

578769

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

AVR280

English

HDMI

An HDMI connection between a source and your display device offers the best possible picture quality.

This connection type is, however, the most limiting in terms of routing, advised cable length and

conversion.

The AVR280 provides two HDMI inputs; these are labelled ‘DVD’ and ‘SAT’ in anticipation of the most

common use for these connectors, but they may be used for any HDMI source. These inputs may be

congured to be associated with any of the other sources, so that selecting that source (‘AUX’, for

example), selects one of the HDMI inputs instead of the usual input associated with that source.

It is important to realise that analogue video sources cannot be routed by the AVR280 to the HDMI

output, nor can either of the HDMI inputs be converted to analogue video (of any sort). The AVR280 acts

simply as a switching device, selecting one of the inputs and routing it to the output.

Keeping the above in mind, it will be necessary (as with the high-quality analogue video connections),

to provide a composite video feed, in addition to the HDMI connection, if the video is to be routed to

Zone 2.

Connecting loudspeakers

The red and black terminals on the back of the AVR280 are used to make the connections to the

loudspeakers. The speakers should be connected to the loudspeaker terminals, refering to the

labels on the rear-panel.

When connecting the speaker terminals of the amplier with the terminals on the speakers

make sure that like polarities are matched (i.e., match ‘+’ with ‘+’ (usually red) and ‘–’ with ‘–’

(usually black)). Mismatching of polarities will result in a weak central sound, unclear orientation

of the instruments and the sense of direction of the stereo being impaired.

There are two options for connecting the speaker cable to the amplier:

Using bare wire ended leads:

1. Strip back the insulation on the wire to reveal about 2cm of conductor (the metal inside

the cable).

2. If the conductor is stranded, twist the strands together tightly to avoid loose strands making

contact with the adjacent terminals or the back panel.

3. Loosen the terminal by turning it anti-clockwise

4. Insert the twisted wire through the hole in the terminal.

5. Tighten by turning clockwise.

When making connections with stranded bare ended wires, take great care that no individual strands of

wire come into contact with the adjacent terminals or with the back panel. If this should happen, it will

cause a short circuit on the output of the amplier and could damage the amplier.

Using spade terminals:

1. Loosen the terminal by turning it anti-clockwise

2. Insert the spade connector under the terminal.

3. Tighten by turning clockwise.











CEN - Centre











 

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam DiVA AVR280 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info