Bedienungsanleitung Arcam DiVA AVR280 (Seite 10 von 38) (Englisch)

578769

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

AVR280

Zone 2 connections

The AVR280 allows independent routing and control of analogue audio and composite

video to a second room such as a kitchen, bedroom or lounge. This second room is known

as ‘Zone 2’.

For Zone 2, the AVR280 outputs a line-level audio signal taken from the stereo analogue

audio, and a composite video signal taken from the composite video input (for a given

source). The analogue inputs are required because there is no analogue-to-digital, DSP

processing or digital-to-analogue conversion available for Zone 2 signals. As the AVR280

does not convert video formats for Zone 2, a composite video signal must also be

connected from the source.

For these reasons, we recommend that source devices that have a digital connection are

also connected via the analogue inputs. High quality YUV/RGB and S-video sources should

also have their composite video outputs connected to the AVR280 for use in Zone 2.

NOTE: As a composite input is required for Zone 2, it may not be

possible to run your DVD player in progressive scan mode and to use

Zone 2 at the same time, unless your DVD player can output both

progressive scan and composite signals simutaneously.

ZONE 2 OUT.

This is the audio output for Zone 2. Connect these to a line level input on

your Zone 2 amplier.

ZONE 2 VIDEO OUT (Composite video connection).

This is the video output for Zone 2. Connect to your Zone 2 video display

using 75Ω low loss coaxial cable.

IN ZONE 2.

This allows the AVR280 to be controlled remotely from Zone 2 via infrared

remote control. See the panel for connection information.

Connecting the AM and FM antennas

FM antenna

An FM antenna is required to receive VHF radio signals.

Although a FM ribbon antenna is supplied as an accessory to the AVR280, for optimal FM radio

reception a roof- or loft-mounted aerial is advised as this will give superior reception. (It is

recommended that any roof-top antenna is tted by an experienced contractor as a contractor

will be able to align your antenna to the nearest FM transmitter.)

In some areas cable radio may be available or, in an apartment building, a distributed antenna

system may be installed. In either of these cases you should have sockets in your home marked

FM or VHF (do not use those marked TV), which should be connected to the FM in socket

the AVR280.

If you wish to use the supplied FM ribbon cable, mount this as high up as possible on a wall with

the ‘T’-elements positioned horizontally. Try each usable wall of the room to see which gives best

reception and use tacks or adhesive tape to secure the aerial in a T shape (note that no tacks

should come into contact with the internal wire of the aerial). When assembled (see box, right), the plug

on the ribbon cable should be connected to the FM in socket

of the AVR280.

AM antenna

An AM antenna is required to receive AM/medium wave radio signals.

An AM loop antenna is supplied as an accessory with the AVR280. This should be attached to the AM

antenna inputs

with one end connected to AM and the other to Ground (it does not matter which way

round this antenna is tted). Rotate the antenna to discover which position gives the best reception.

In areas of weak reception, or when the AVR280 is in use inside a steel framed building (such as an

apartment building), you can use a wire between 3 and 5 metres long to strengthen reception. Mount

this high up outside the building (if possible) and connect one end of this wire to the AM antenna input

in addition to the loop aerial supplied (do not disconnect the AM loop antenna).



The AM tuning ‘step size’ needs to be set according to your location. This is done using the switch on the

rear panel

: set it to 10kHz if you are in North America or 9kHz anywhere else. Note that this should

be set correctly even if you do not intend to use AM reception as it also alters some FM tuner settings for

use in North America.



























2) insert the spade





3) re-tighten the screws









































  

Zone 2 remote controller connection.

A receiver compatible with this connector

available from Xantech (part no. 291-10). Please

contact a Xantech registered dealer for this part,

as ARCAM does not stock them.

See www.xantech.com for more information.

The 3.5mm jack plug for this connector is wired

as follows:

3.5mm stereo jack Function

Tip Signal

Ring 0V

Sleeve 12V,

30mA current-limited

This follows the Xantech standard for IR

transmission over wire.

Arcam DiVA AVR280 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info