Bedienungsanleitung Arcam solo movie 5 1 (Seite 8 von 30) (Englisch)

371605

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

To view the pictures from Solo Movie 5.1 you need

to connect one of its video outputs to your display

device (TV, monitor, projector, etc.).

Solo Movie 5.1 has three of the four video output

options described below. All versions of Solo Movie

5.1 have HDMI and Composite outputs. In addition,

and depending on the shipping region, your unit

will have either SCART or Component video

connectors, to match the connections typically used

in your region. You need only use one type of video

connection from those available; choose a type that

your display device supports. If your display device

does not support any of the above connection types,

you may need to update your display to use it with

Solo Movie 5.1; in this case, please contact your dealer

for further assistance.

Video inputs

You can use other video equipment (satellite/cable

receivers, games consoles, etc.) with Solo Movie

5.1. Connect these to the audio and video inputs of

Solo Movie 5.1. You can use any of the video inputs

provided, but the same type of connector should also

be used to connect Solo Movie 5.1 to the display

device.

Solo Movie 5.1 does not convert video formats, so

if a video source is connected (for example) via the

COMPOSITE VIDEO SAT input, it is only available at the

COMPOSITE VIDEO OUT socket.

HDMI digital video

The HDMI connector offers uncompressed digital

video and audio transmission between Solo Movie

5.1 and the display device, and provides the highest

quality output. Generally, it is also the easiest

connection type to conﬁgure.

To use this video connection,

you’ll need a HDMI or HDMI/

DVI cable between Solo Movie

5.1 and your display device or

receiver. Arcam recommends

that you use high quality HDMI

cables for the best results.

In the Video set-up menu (see page 17), ‘Video

Resolution’ should be set to ‘Auto’. The unit will

conﬁgure its video output automatically to match the

capabilities of the attached HDMI device.

Component video

Use three 75Ω phono cables to

connect the Component Y, Pb,

Pr outputs of Solo Movie 5.1 to

the Y, Pb, Pr inputs of the display

device. Ensure that the cables are

suitable for video use and that

they are approximately the same

length.

If your television is capable of accepting a

progressively scanned (de-interlaced) video signal, you

may wish to use the progressive video output from

Solo Movie 5.1. If you are unsure whether your display

device can accept progressive video, please refer to its

instruction manual or consult your dealer.

Some component video interfaces are labelled

differently to the back panel of Solo Movie 5.1; check

the table if the component inputs of your display

device are not labelled ‘Y, Pb, Pr’.

SCART output

The SCART connector is

common on European A/V

equipment and provides a

convenient connection

method between Solo Movie

5.1 and display device, carrying

both video and stereo audio.

If you are using a SCART connection and you do not

wish to listen to the audio through your TV, then it is

best to mute your TV’s speakers; muting the TV will

prevent this audio being heard.

Note that the SCART output has a control signal

that switches your TV to its SCART input when Solo

Movie 5.1 is turned on. It will also signal to wide-

screen TVs the correct aspect ratio (16:9 or 4:3),

provided this feature is supported by the TV.

video connections

Solo

Movie 5.1

alternative alternative alternative

Y Y Y Y

Pb Cb (B–Y) U

Pr Cr (R–Y) V

Composite video

If your display device offers only a

composite input (sometimes labelled

CVBS or just ‘video’), connect this to

the COMPOSITE VIDEO OUT socket

of Solo Movie 5.1 using a 75Ω

phono cable suitable for video use.

Note that a composite video connection gives the

lowest-quality output; if your display device supports

other video connection types, we advise you use

them instead.

Using two video connections

simultaneously

In some circumstances, it is possible to use two video

connections simultaneously (routing one connection

to a second room or display, for example). If you wish

to do this, please read these notes:

The Composite video and SCART outputs

are only active if HDMI is not connected (or

if ‘HDMI Resolution’ is set to ‘SD Progressive’

– see page 17). These two output types carry

interlaced output at all times.

The Component video output is only active if

HDMI is not connected (or if ‘HDMI Resolution’

is set to ‘SD Progressive’ – see page 17). It can

be set to carry either interlaced or progressive-

scan output.

The HDMI output is active only if a compatible

display is detected by the Solo Movie 5.1. It can

be set to carry either interlaced, progressive-

scan or high-deﬁnition output.

About HDMI

HDMI (High Deﬁnition Multimedia Interface)

supports both video and audio on a single digital

connection for use with DVD players, digital TV,

set-top boxes, and other AV devices. HDMI was

developed to combine the technologies of High-

bandwidth Digital Content Protection (HDCP)

and the Digital Visual Interface (DVI) in one

speciﬁcation, with the addition of transmission of

digital audio information; HDCP is used to protect

digital content transmitted to DVI-compliant

displays.

HDMI has the capability to support standard

or high-deﬁnition video and stereo audio. HDMI

features include uncompressed digital video,

one connector (instead of several cables and

connectors), and communication between the AV

source and AV receivers.

Arcam solo movie 5 1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam solo movie 5 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info