Bedienungsanleitung Arcam solo movie 5 1 (Seite 7 von 30) (Englisch)

371605

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

English

movie 5.1

solo

IN LOCAL – This allows remote control

signals to be received by Solo Movie

5.1 if the remote sensor is covered (or

otherwise not ‘visible’ to the remote

control). An external sensor is used to

receive the signals from the remote

control, which are then fed to Solo

Movie 5.1 (into this input) using a

suitable cable.

IN ZONE 2 – Use this connector if you

are using a second room system that has a

remote sensor. The external sensor is used to

receive the signals from the remote control,

which are then fed to Solo Movie 5.1 (into this

input) using a suitable cable.

Listening with headphones

The front-panel of Solo Movie 5.1 has a socket

for connecting headphones. To use headphones

with the unit, plug the headphones into the

socket on the left hand side of the front panel

– the main speaker output and the pre-amp.

output are muted

automatically but Zone 2

output remains active.

This socket accepts

headphones with an

impedance rating between

32Ω and 600Ω, ﬁtted

with a 3.5mm stereo

jack plug. The headphone

socket is always active,

except when Solo Movie

5.1 is muted.

MENU SOURCE INFO OK

POWER

VOLUME

TAPE

�

�

Audio outputs

PRE OUT: To drive a Low Frequency Effects speaker (a

subwoofer), or if you require more power than Solo

Movie 5.1’s 50W per channel, you can connect an

external power ampliﬁer. Connect the PRE OUT

sockets to the input sockets of your multi-channel

power ampliﬁer, then connect your speakers

(including the Subwoofer, if required) to their speaker

terminals.

ZONE 2/REC OUT: This is the output to be used for connecting to an audio

recorder or for a second room system. It should be connected by Phono–

Phono (RCA) cables to the ampliﬁer in the second room. When used

for a second room, the volume can be controlled by the remote control

in Zone 2 or from the Zone 2 menu. The output level can vary with the

volume control for the second room (see page 18).

Audio inputs

Solo Movie 5.1 provides four audio inputs, allowing

connection of other audio sources, (a games console,

TV, satellite tuner, etc.). Three of these inputs are on

the rear panel, with one on the front panel. The labels

above the inputs give suggested uses, but all four

inputs have the same characteristics (all are line-level

inputs) and any suitable device may be connected to

any input. (Note, however, that the name of the input

shown on the front-panel display cannot be changed.)

To connect a device to an input on the rear of Solo

Movie 5.1, use a stereo phono cable of a suitable

length; for connection to the front-panel, the cable

MENU SOURCE INFO OK

POWER

VOLUME

TAPE

�

�

must terminate in a stereo 3.5mm jack plug. Connect

the audio output of the device to one of the inputs

of Solo Movie 5.1, making sure that the plugs are

pushed in ﬁrmly. We advise you to use high-quality

interconnect cables wherever possible to ensure the

best possible sound quality.

Connecting a record deck

Solo Movie 5.1 is not ﬁtted with a phono pre-ampliﬁer.

If you wish to connect a record deck to Solo Movie

5.1, then you will need an external pre-ampliﬁer.

Please contact your dealer for further information and

recommendations on the best option for you.

These connections are intended for use in multi-room

installations. Normally there is no need to make any

connections to these sockets. If you would like to

make use of these features, however, please download

the document ‘Solo Remote Control’ from our web-

site (www.arcam.co.uk), which includes advice on how

to make these connections.

12V TRIGGER – This output provides a 12V signal

whenever the unit is switched on (i.e., not

off or in stand-by). This signal can be used to

switch power ampliﬁers (or other compatible

equipment) connected to Solo Movie 5.1 on

automatically when the unit is activated.

OUT – This output carries all signals

from the front-panel remote-

control receiver, plus commands

received through the two external

sensor inputs (‘In Local’ and ‘In

Zone 2’). This can be used to

route remote-control commands

to other equipment (potentially in

different locations). For example,

ampliﬁer commands could be

received by Solo Movie 5.1, then routed to

ampliﬁer in a remote location using this output

connector.

Remote control inputs/outputs and the 12V trigger

AERIAL

INPUT

iPod

control

Music and pictures from your iPod can be fully

integrated with your system using Arcam’s rDock

or rLead. Solo Movie 5.1 takes over the control and

ampliﬁcation, with iPod text appearing on the front

panel display of the unit. Full details of connecting up

and using the CR100 for remote control are given in

the rDock or rLead quick start guide supplied with

these accessory units.

RS232 control

Solo Movie 5.1 has an RS232 serial connector that

allows control from a PC or similar device. Full details

of the RS232 control protocol are given on the

Arcam website.

audio connections

DIGITAL AUDIO OUT: This is an optical output (TOSLINK),

carrying digital audio output. This can be used for making

digital recordings using compatible recording devices (such

as MiniDisc). CD playback is at 44.1kHz; DAB radio (where

ﬁtted) plays 48kHz, DVD playback is at 48kHz or 96kHz,

and DVD-A is at up to 96kHz. Digital output from analogue

inputs is at 44.1kHz. SACD discs do not provide digital

output.

Digital audio inputs

Solo Movie 5.1 provides three digital audio inputs: an AUX (optical) input, and two

SAT inputs (one optical and one coaxial). If a signal is connected to both SAT inputs,

the coaxial input takes priority over the optical input.

Digital inputs take priority over analogue inputs for the same source. So if both

analogue and digital inputs are connected to the same input source, Solo Movie 5.1

will use the digital signal.

Arcam solo movie 5 1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam solo movie 5 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info