Bedienungsanleitung Arcam solo movie 5 1 (Seite 9 von 30) (Englisch)

371605

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

English

movie 5.1

solo

speaker positioning

standing speakers), or in corners. The speaker drivers

should be at, or a little above, ear level when seated.

If possible, centre your seating area between the

surround speakers.

The ﬁnal sound will depend on the acoustics of

the listening room and experimenting with speaker

positioning is very worthwhile.

Subwoofer

The location of the subwoofer (Low Frequency Effects

speaker) will affect the overall sound quality. Placing the

subwoofer next to a wall or in a corner will often boost

efﬁciency and give a cleaner low bass sound. However,

all rooms react differently and we recommend that you

experiment with subwoofer positioning.

Speaker stands

The more ﬁrmly a speaker is held, the better it will

sound. We recommend the use of rigid metal stands of

40–60cms height. Properly damped types that do not

‘ring’ when tapped with a pencil (either by virtue of

construction, or because they are ﬁlled with dry silver

sand) will bring out the best in a speaker. Ensure that

the stands and/or speakers do not wobble.











Connecting speakers

Solo Movie 5.1 is designed to drive a set of ﬁve full-

bandwidth speakers, rated between 4 and 8 ohms.

The unit is ﬁtted with speaker terminals that can

accept either spade terminals or bare wires.

The ﬁve full-bandwidth speakers are: LS (Left

Surround), L (Left), C (Centre), R (Right) and RS

(Right Surround). An active subwoofer may be

connected to the SUB output. To place the speakers

in your listening room, see the panel below.

To connect each of the ﬁve speakers, unscrew

the corresponding terminals on the back of Solo

Movie 5.1, insert the speaker wires (or spades)

and screw the terminals back up. Make sure

that the red (positive/+) terminal of the speaker

is connected to the red (positive/+) terminal

on the back panel, and the black (negative/–)

terminal of the speaker is connected to the black

(negative/–) terminal on the back panel.

It is important that no stray strands of wire from

these connections are allowed to touch another cable

or the product casing. Failure to ensure this can cause

a short circuit and damage your Solo Movie 5.1.

Do not over-tighten the loudspeaker terminals, or use a

wrench, pliers, etc., as this could damage the terminals

and this would not be covered under warranty.

Speaker cables

The speakers should be connected to the ampliﬁer

using good-quality, high-purity, copper cables. Solid

core cables, or those with surface-only conductors,

are particularly suitable. Bell wire and very cheap

speaker cables should be avoided – they are a false

economy and can signiﬁcantly degrade the sound

quality.

The cable runs to the two speakers should be of

roughly equal length and yet as short as practicable.

Connections to the speaker terminals should

always be tight, whether using bare wires or spade

connectors, but do not use tools such as pliers,

wrenches or spanners to tighten the connectors as

these may cause damage to the terminals.

speakers

The advice given here is a general guideline for setting up speakers.

Refer to the documentation supplied with your speakers for

more precise positioning and installation information, and see

www.dolby.com/consumer/home_entertainment/roomlayout.html for

useful information on listening-room layouts.

Room acoustics

Your room’s shape and how it is furnished will affect the sound you

hear. For instance, too many bare surfaces can cause reﬂections that

may add harshness to the sound. Carpets, wall-hangings and curtains

can all help.

If you have a choice of listening rooms, avoid one that is perfectly

square or has one dimension exactly twice another. Such a room can

aggravate resonances that colour the sound.

The closer you place a speaker to corners and the intersection of

wall and ﬂoor or wall and ceiling, the stronger the bass output, which

may over-emphasise the bass. Moving a speaker just a few inches can

sometimes make a big difference.

Speaker setup

Proper speaker placement is the key to the best home theatre sound

(see diagram).

As a rough guide, speakers should be placed on rigid stands at about

15cms from the rear wall and at least 60cms from any side wall.

Speakers should never be placed on the ﬂoor (unless they are ﬂoor-

AERIAL

INPUT

AERIAL

INPUT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Arcam solo movie 5 1 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Arcam solo movie 5 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info